ECAP细化晶粒法的仿真与分析

ECAP(Equal Channel Angular Extrusion)方法，是实现材料纯剪切变形的有效方法。本文采用有限元（FEA）分析软件ANSYS对Al的挤压过程进行仿真与分析。分析结果表明：外切角Φ、圆角半径、试样与凹模之间的摩擦系数、凹模本身的特性（如弹性模量、泊松比等）等等，对材料的变形量都有不同程度的影响。     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。     

Hypervelocity impact computations with finite elements and meshfree particles

The ability of computations to model characteristics of hypervelocity impact is demonstrated using an algorithm for the automatic conversion of distorted finite elements to meshfree particles. The Lagrangian formulation tracks material boundaries and properties without the errors typical in an Eulerian formulation as the material traverses large distances. A computation of a sphere impacting a bumper is shown to reproduce three regions in the debris cloud that are observed in tests: a front region composed of droplets of melted projectile and target, a middle region of fragmented projectile, and a back region of spalled projectile. Additional computations reproduce the observed traits that result from variations in the projectile shape and obliquity. The computation of a projectile impacting spaced plates demonstrates the ability of the method to model the damage to the rear plate of a Whipple shield for spacecraft protection.     

刚性圆板自由落体在水面上的冲击压力

本文对一个刚性圆板自由落体在水面上的冲击过程建立了比较精确的理论模型,并建立了相应的数值格式。计算结果与已有的实验结果符合良好,通过计算进一步给出了下落质量和下落高度对冲击压力峰值的影响。     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Flame retardant and the degradation mechanism of high impact polystyrene/Fe-montmorillonite nanocomposites

High impact polystyrene/Fe-montmorillonite (HIPS/Fe-MMT) nanocomposites were successfully prepared by melting intercalation. The nanostructures of HIPS/Fe-MMT were testified by X-ray diffraction (XRD) and transmission electron microscope (TEM). Corresponding to pure HIPS, the thermal stability of HIPS/Fe-MMT nanocomposites was notably improved. The peaks of heat release rate (PHRR) and the mass loss rate (MLR) were significantly reduced after the formation of the HIPS/Fe-MMT nanocomposites from cone calorimetry. And nanocomposites PHRR was further lower with the increase of Fe-MMT content in the range of 1 to 5 wt%. The degradation mechanism of HIPS and HIPS/Fe-MMT nanocomposites was conducted by pyrolysis gas chromatography mass spectrometry (Py-GC-MS). And the reason of the enhancement of thermal stability maybe is that structural iron is the operative site for radical trapping in the Fe-MMT and the nanostructure enhances the interaction of the chains of the HIPS.     

Expert identification and selection: Legal liability concerns and directions

Legal liabilities pertaining to the identification and selection of domain experts is an issue that could adversely impact expert systems developers. Problems pertaining to flawed knowledge, improperly defined expertise, and behavioural and psychological impediments are just some of the issues. This paper examines the torts of strict products liability and negligence that system developers could incur as a result of expert-related difficulties. Parallels from legal scholars and federal and state court decisions are discussed relevant to expert system projects and developers. The paper concludes with a presentation of steps that systems developers can take to minimize potential legal liability.     

HDPE的耐磨蚀性与抗冲击性的研究

用自制的旋臂式磨蚀实验仪，研究了５种高密度聚乙烯和１种顺丁橡胶改性的高密度聚乙烯，在铁尾矿和铁精矿浆体中的耐磨蚀性。耐磨蚀性最差的是ＨＤＰＥ２２００Ｊ，耐磨蚀性较差的是ＨＤＰＥ６３００Ｍ；ＨＤＰＥ５０００ｓ，６０９８和２４８０的耐磨蚀性较好；ＨＤＰＥ／ｃｉｓ－ＢＲ的耐磨蚀性最好。     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

介绍一种生产冲挤用铝合金坯料的新工艺

哈兹列特铝板带连铸连轧工艺已被成功地用于铝和铝合金冲击挤压用坯料的生产。在对哈氏四个有关用户扫描的基础上，列举了其产品及其用途，并介绍了相关工艺及其优点。