人工智能对国内劳动就业影响研究综述

利用citespace关键词共现分析方法,梳理了1980年以来人工智能对劳动就业影响的国内相关文献,发现目前的研究议题主要包括人工智能影响就业的机制、人工智能对就业规模的影响、人工智能对收入分配的影响、人工智能对就业形态的影响、人工智能对劳动过程与劳动关系的影响. 总体来看,目前的研究主要集中在与劳动力市场相关的议题; 理论性的论述占大多数,而具有说服力的实证研究较少; 宏观性的研究较多,深入企业与生产现场考察的微观研究较少. 未来应进一步拓展研究主题,进行多种视角与跨学科研究,重视实证研究与微观研究.     

Structure and Properties Characterization of Ceramic Coatings Produced on Steel Using a Combined Technique

STEEL is the most widely used material in engineering,but unfortunately,steel exhibits poor wear resistanceand obvious contact corrosion.For decades,researchersprepared coatings on steel to improve its properties;ceramic is one of these coatings.To obtain ceramiccoatings on steel,many researchers use techniques suchas plasma spraying,laser cladding,etc.,but some ofthem are too expensive,some of them have a deep heataffected zone in the substrate,and some of them cannot bond well with the subs…     

改善Fe-B-C合金韧性的研究

为了提高Fe-B-C合金的韧性,应用稀土-钛-氮复合变质剂改善Fe-B-C合金组织和性能。结果发现,Fe-B-C合金复合变质处理后的凝固组织明显细化,且组织分布均匀,并出现钛硼化合物,钛硼化合物不同于普通Fe-B-C合金中的Fe2B呈网状分布,而是呈断网状和块状分布,特别是经高温热处理后,硼化物变成球状和棒状,Fe-B-C合金韧性明显提高,由8～10 J/cm2提高至22～25 J/cm2。经变质处理的Fe-B-C合金可用于制造轧钢机导卫板,其耐磨性比高镍铬合金钢提高1.3倍。     

Lipid Droplet Motility Increases Following Viral Immune Stimulation

Lipid droplets (LDs) have traditionally been thought of as solely lipid storage compartments for cells; however, in the last decade, they have emerged as critical organelles in health and disease. LDs are highly dynamic within cells, and their movement is critical in organelle–organelle interactions. Their dynamics are known to change during cellular stress or nutrient deprivation; however, their movement during pathogen infections, especially at very early timepoints, is under-researched. This study aimed to track LD dynamics in vitro, in an astrocytic model of infection. Cells were either stimulated with a dsRNA viral mimic, poly I:C, or infected with the RNA virus, Zika virus. Individual LDs within infected cells were analysed to determine displacement and speed, and average LD characteristics for multiple individual cells calculated. Both LD displacement and mean speed were significantly enhanced in stimulated cells over a time course of infection with an increase seen as early as 2 h post-infection. With the emerging role for LDs during innate host responses, understanding their dynamics is critical to elucidate how these organelles influence the outcome of viral infection.     

冲击荷载作用下热处理花岗岩动态力学特性研究

为研究冲击速度和热处理温度对黑云母花岗岩动态力学特性的影响,利用改进的霍普金森压杆系统对25~800 ℃共9个温度等级的热处理试样分别进行3种弹速下的冲击压缩试验。试验结果表明：随着冲击速度的增加,25~700 ℃热处理试样的应力—应变曲线由“Ⅱ型”转变为“Ⅰ型”,而800 ℃热处理试样均表现出“Ⅰ型”应力—应变曲线特征。同一温度热处理下试块的峰值应力、应变和平均应变均随动荷载的升高而增大。相同的冲击速度下,300 ℃热处理试样的动力学性能有所改善,500 ℃后试样的动力学性能开始逐渐劣化。同一温度热处理试样的破碎程度随冲击速度的增加而增加;相同冲击速度下,热处理试样的破碎程度随温度的升高先减弱后增强。     

淬火温度对铸造Fe—B—Ti合金组织和性能的影响

通过不同的热处理淬火温度改变铸造Fe—B—Ti合金的组织，探讨了铸造Fe—B—Ti合金不同组织与性能的关系。试验结果表明：淬火温度较低时，硼化物变化较小，网状分布趋势明显；淬火温度较高时，硼化物断网和团聚化趋势明显加快。淬火温度1050℃时，硼化物网状特征消失，基本上都变成了团块状、颗粒状和杆棒状分布。随着淬火温度升高，硬度和韧性增加，超过1000℃，硬度和韧性变化不明显。淬火温度1050℃时，综合性能良好。     

16MnR 容器板性能不合格的原因

运用扫描电镜、金相检验和力学检验对不合格的16MnR容器板进行了检验分析。结果表明，材料中的条状MnS夹杂物和少量的马氏体、贝氏体组织是导致钢板延伸、冲击性能不合格的主要原因。     

25Cr3Mo3NiNb二次硬化钢冲击性能的研究

研究了二次硬化钢25Cr3Mo3NiNb的冲击韧度随回火温度和试验温度的变化.结果发现,试验钢在200℃回火时冲击韧度较高,300～600℃回火时冲击韧度值较低,600℃以上回火时冲击韧度值迅速升高,640℃回火时冲击韧度达到最高值55J/cm2,640℃以上回火时冲击韧度值有所降低.640℃回火后试验钢的冷脆转变温度为10℃,屈服强度为960MPa,可以满足兵器特种结构件高强度高韧性的要求.     

Impact toughness of tungsten films deposited on martensite stainless steel

Tungsten films were deposited on stainless steel Charpy specimens by magnetron sputtering followed by electron beam heat treatment. Charpy impact tests and scanning electron microscopy were used to investigate the ductile-brittle transition behavior of the specimens. With decreasing test temperature the fracture mode was transformed from ductile to brittle for both kinds of specimens with and without W films. The data of the crack initiation energy, crack propagation energy, impact absorbing energy, fracture time and deflection as well as the fracture morphologies at test temperature of-70 ℃ show that W films can improve the impact toughness of stainless steel.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。