HART协议物理层设备的测试（II）

本文介绍HART协议物理层设备的测试要求、测试设备、测试方法及测试时的一些特别说明。     

W‐band physical layer design issues in the context of the DAVID–DCE experiment

This paper aims at focusing on the aspects concerning the physical layer design for an innovative satellite communication experiment. Such an experiment, denoted by the acronym DAVID–DCE (Data and Video Interactive Distribution—Data Collection Experiment) is based on the exploitation of the W‐band (75–110 GHz) for high‐bit‐rate satellite transmission. The potential advantages of using of the W‐band are mainly related to the great bandwidth availability, and to the absence of interference. Moreover, an expected result of the experiment is a substantive improvement in the communication system's performances in the presence of meteorological phenomena (e.g. rain) as compared with the more conventional Ka‐band satellite transmission. On the other hand, problems to be faced concern the non‐ideal behaviours of hardware devices employed for high‐frequency digital transmission. In particular, carrier recovery and timing recovery are the most crucial signal‐processing tasks to be carefully considered in the design of the physical level of the system, because they considerably suffer from hardware impairments. The purpose of this work is to illustrate the proposed solutions in terms of the most critical modulation, demodulation and synchronization design issues, together with the effects of non‐ideal behaviours of hardware components on BER performances. Copyright © 2004 John Wiley & Sons, Ltd.     

Optical and structural properties of MOVPE grown GaxIn1−xAs/InP strained multiple quantum well atructures

This paper presents a study of the structural and optical properties of strained GaInAs/ InP multiple quantum well (MQW) structures fabricated by LP-MOVPE. The composition of the Ga _x In_1−x As films ranged fromx = 0.17 tox = 1.0 and was determined by sputtered neutral mass spectrometry (SNMS) on thick layers. The structures of the MQW samples with well widths from 1.5 to 5 nm were investigated by high resolution x-ray diffraction (HR-XRD). Simulations of the diffraction patterns showed that transition layers of approximately 2 monolayer (ML) thickness with high lattice mismatch exist at the interfaces. Photoluminescence (PL) measurements indicate well widths of a multiple of a monolayer with local variations of one monolayer. The PL peak energies vary smoothly with the Ga concentration. These results were confirmed by optical absorption measurements.     

在建坝体中部分浆砌石的控制爆破拆除

某在建大坝部分浆砌石坝体因质量不合格须爆破拆除。保护余留坝体免受爆破影响是此工程的重点,为此,采用了小直径浅孔和微差爆破分层拆除方法,被拆除部分和被保护部分之间预留保护层。爆破施工过程中,利用超声波观测法和压水试验法判断被保护坝体是否受到了爆破震动的影响。根据判断结果,调整爆破参数,以减小爆破震动。文中论述了爆破参数的选择、保护层厚度的确定,同时介绍了安全控制技术、测点布置以及监测结果。     

主动约束层阻尼板结构动力学建模研究

将有限元法和GHM法相结合，给出了建立主动约束层阻尼（ACLD）板结构动力学模型的新方法。建模时，考虑到粘弹材料（VEM）的纵向位移影响，采用GHM方法描述VEM的本构关系，解决了VEM的力学特性随温度和频率变化的难点，避免因VEM的复杂本构关系而产生的微分积分方程。算例表明本文给出的建模方法是准确的，ACLD结构能够有效控制结构振动。     

挡土墙填土曲线破裂面的地震主动土压力分析

在地震作用影响下，墙后填土处于极限平衡状态时，假定破裂面为一条通过墙趾的旋轮线。从墙后土楔中取出一微薄水平层，研究其在水平惯性力下的平衡，得到的地震土压力分布和土压力合力作用点位置均与实验结果相吻合。     

球化退火态钢脱碳层深度的金相法测定

论述了国内外金相测定球化退火钢脱碳层深度的标准方法和常用方法存在的不准确性和不适用性问题,提出了解决问题的途径——定量金相法。     

二维无机功能材料

简要介绍了一种通过层状结构材料剥离成单分子层的无机二维功能材料。     

STN—LCD的新进展

STN-LCD采用新的取向层,消除了残象;采用新的驱动波形,消除了串扰;采用二(口恶)烷、卤化物、链烯基、醚和二苯乙炔,改进了液晶料材的性能,使STN-LCD获得高的对比度、快的响应速度、低的驱动电压;采用有源矩阵驱动方法,消除了帧响应,使STN-LCD获得高的对比度、高的亮度及视频响应速度;使用温度跟踪电路,自动跟踪STN-LCD的阀值电压,使STN-LCD获得宽的工作温度。