Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

试论双点后方交会简便公式

根据双点后方交会的图形特点和已知条件，列出了方程组，推导出了双点后方交会直接计算座标的简便公式，同时求出了精度计算公式，以供测量人员参考     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

异质谷间转移电子器件的计算机模拟

使用弛豫时间近似求出了描述两能谷间电子交换的方程。在此基础上建立了双能谷电子的连续性方程和油松方程。对具体的ＧａＡｓ／ＡｌｘＧａ１－ｘＡｓ异质谷间转移电子器件结构求解了这些方程组，得到了直流工作时器件内的电场分布、双能谷中载流子的布居以及两个能谷的电流分布。这些结果正好和常规Ｇｕｎｎ器件相反，说明了两种器件的不同工作机理。最后通过对低Ａｌ组份势垒结构的计算说明了Ｘ谷电子注入对器件工作的重要作用。     

掺气减蚀设施水力计算的改进

结合小湾工程泄洪洞模型试验进行了11种挑跌坎型和6级流量的试验观测，据此提出了特别适用于大单流量条件的射流出射角修正式，提出了射流近底流速的选取原则.与实验资料对比证明本文计算方法有足够精度。     

参数三次B样条曲线的一种整体光顺方法

本文在能量法的基础上，提出了一种新的目标函数，给出了参数三次Ｂ样条曲线的一种新的整体光顺方法。利用这种方法得到的曲线不仅具有较小的应变能，而且曲率变化比较均匀，具有很好的光顺效果。该方法能推广到对曲面的光顺。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

对等张力链条机构设计的再思考

为解决震源在振动器提升后链条与销轴的断裂问题,应采用等张力原理对链条提升机构进行改进设计。经野外实践证明,这种机构基本上能够满足野外工作的要求。本文对目前所采用的机构形式可能存在的改进设计进行了分析。     

长25-29井卡钻事故的处理

长２５－２９井在完井阶段通井过程中发生粘附卡钻事故，在处理卡钻过程中又发生卡套铣筒、井漏、溢流等事故及复杂情况。通过对井下情况的认真分析，采取先堵漏后循环再解卡的处理方案，顺利地解除了该次卡钻事故，大大地减少了经济损失。