应用频率-初速法测试推算单桩承载力须解决的几个关键问题

本文对当前频率 -初速法应用中存在的一些问题阐述了作者的看法并着重探讨桩振初速度V0的计算方法、W0 的正确单位、如何使桩 -土体系明显震动、怎样从激振曲线中突出及分离出桩振曲线 ,从而获得正确的桩振频率f0 和首波峰 -峰值Ad、动静对比系数 βv 的选取     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

关于离散Kirchhoff薄板单元的研究

本文对离散Kirchhoff薄板单元进行了深入的分析。文中将用于建立离散Kirchhoff单元的泛函分为三部分,分别用应变第一不变量、绕Z轴的转动偶和有关的单元边界上的积分来表达,并阐明了各部分的作用。其中单元的收敛性质完全由第一、三部分所决定,而第二部分则控制了单元的计算精度。在此基础上,文中建议了一种提高离散Kirchhoff单元精度的新方法,并由此推导了一个任意四边形离散Kirchhoff单元。计算表明,本文的改进单元与原来的离散Kirchhoff单元及其改进型相比,计算精度有了显著提高。     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

鱼雷捷联系统动基座精对准的卡尔曼滤波法

为解决鱼雷捷联系统的初始对准，提出了失准角及陀螺随机常值漂移快速估计方法，经数字仿真，对缩短初始对准时间，提高初始对准精度有较好的效果。     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Temperature–stress–strain trajectory modelling during thermo-mechanical fatigue

The isothermal strain‐life approach is the most commonly used approach for determining fatigue damage, particularly when yielding occurs. Computationally it is extremely fast and generally requires elastic finite element analyses only. Therefore, it has been adapted for variable temperatures. Local temperature—stress–strain behaviour is modelled with an operator of the Prandtl type. The hysteresis loops are supposed to be stabilized and no creep is considered. The consequences of reversal point filtering are analysed. The approach is finally compared to several thermo‐mechanical fatigue tests and the Skelton model.