济钢小板坯连铸机φ360mm拉辊优化改造

为解决小板坯连铸机φ360mm拉辊断颈、断辊问题，对拉辊原设计及现场使用条件进行了分析，将材质由55^#锻钢改为35CrNiMo，辊身与辊颈处改为圆锥台式，同时加大辊颈处过渡圆弧并磨削处理，延长水冷孔通过辊颈圆弧，从而使拉辊寿命由3～4个月延长到10～12个月，减少了事故损失，加快了生产节奏，年直接经济效益达49万元。     

误读与纠正

分析材料试验机度盘偏转角度小 (准确度低 )、试样打滑、定义 (上屈服强度 -下屈服强度 -屈服强度 )模糊、不同应力速率等导致误读 ,并针对误读原因提出纠正方法。     

静载荷和疲劳载荷作用下 C/Al 正交层压板的力学响应

本文讨论静载荷及疲劳载荷作用下 C/Al 正交层压板的力学响应,并考虑损伤过程中的临界现象,以此作为结构设计准则的基础。对静载荷作用的情况:(1)90°铺层的门槛应变ε_(FPF)随着约束程度增加而增加,而且开裂后的行为也受约束程度的影响。(2)经历加载-卸载再重新加载至断裂的过程后,初始试样存在一个剩余永久变形,其损伤状态可以用刚度的变化来表征;而疲劳试样在加载-卸载过程中刚度变化很小,反映其损伤达到一个稳定的状态。对疲劳载荷作用的情况:(1)对于给定的应力比 R,试样会趋于与它所承受的 S_(max)最大值相应的 SDS 状态。循环应力范围的不断增大,会引起基体损伤的增加,从而重新建立新的饱和损伤状态。(2)对于每一损伤状态均有一对应的循环应变范围 Δε。在 SDS 状态下,Δε保持不变。(3)以刚度下降为损伤参数对 C/Al 层压板进行了降级应力分析,并由此来预计在ΔS_(sh)以下,层压板不会发生疲劳损伤累积。     

差动光栅在精密测试中的应用

提出差动光栅概念,举例说明差动光栅在光纤面板刀口响应测试和材料形变自动监测系统等精密测试中的应用。     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

4TYD112型离心空压机联轴器故障的分析及处理

对新冶钢动力厂制氧机组配套的原料空气压缩机故障现象进行了原因分析,并有针对性地提出了处理措施,经运行检验,故障基本消除。     

Electron microscopic observations and DNA chain fragmentation studies on apoptosis in bone tumor cells induced by ~(153)Sm-EDTMP

ＥｌｅｃｔｒｏｎｍｉｃｒｏｓｃｏｐｉｃｏｂｓｅｒｖａｔｉｏｎｓａｎｄＤＮＡｃｈａｉｎｆｒａｇｍｅｎｔａｔｉｏｎｓｔｕｄｉｅｓｏｎａｐｏｐｔｏｓｉｓｉｎｂｏｎｅｔｕｍｏｒｃｅｌｓｉｎｄｕｃｅｄｂｙ１５３ＳｍＥＤＴＭＰＺｈｕＳｈｏｕＰｅｎｇ，Ｘｉａ...     

Energetics of Plastic Deformation of Metastable Austenitic Stainless Steel

The change in the internal energy during uniaxial tensile deformation of austenitic stainless steels EN 1.4301 (AISI 304) and EN 1.4318 (AISI 301LN) was determined by measuring the extent of γ→α'‐martensite transformation and the temperature increase of the samples. From the results the fraction of the stored energy of cold work and the free energy change related to the strain‐induced γ→α'‐martensite transformation were determined. The fraction of stored energy varied around 0.4. With the metastable steel grades the free energy change related to the γ→α'‐martensite transformation was found to vary between ‐98 MJ/m³ and ‐206 MJ/m³ depending on the austenite stability of the steel. Furthermore, the magnitude of the mechanical driving force was estimated by comparing the results with the free energy change of thermally induced transformation.     

铁铝酸盐复合膨胀水泥化学预应力机理及其应用研究

本文阐述铁铝酸盐自应力混凝土的主要物理力学特征.研究了限制膨胀应变与配筋率之间的定量函数关系.通过正交试验和方差分析,确定了复合外加剂对其性能的影响.针对其在自应力管中的应用,提出多层中空圆柱理论计算模型,按弹性理论计算出自应力管初始应力分布规律.对比以前的线性理论计算误差,给出相应的修正系数.本文对类似的自应力混凝土,具有普遍的指导意义.     

Hardness-stress-strain correlation in aluminium—A simpler alternative to visioplasticity in metal forming

Local stress and strain variations in the deformation zone can be ascertained by measuring hardness. Hardness is correlated with strain and stress. The expressions discussed later are useful in determining the local variations in stress and strain from hardness measurement. It is a simple method compared to visioplasticity. One can estimate the forces required for a forming process. It helps in the choice of equipment, design of tooling and selection of lubricant for the particular process.