SF6气体绝缘电容式电压互感器研制

本文介绍西容公司新研制的一种完全无油化的SF6气体绝缘电容式电压互感器,提出了关键技术问题解决方案和产品绝缘结构的设计思路.并介绍了研制成功的110kV和220kV系列产品的结构、技术参数、性能指标、试验考核情况和产品特点.     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

液氨储罐保冷改造效果评定

作者结合实例，论述了氨罐保冷改造的设计、选材及施工，给出了改造后两年的测试结果，并对测试结果进行了分析。     

中小型变压器供电电机起动方式的选择

通过分析和计算及实例，从允许电压降范围和电动机母线电压校验两方面叙述了电动机起动时如何合理地选择起动的方式。     

The chloride stress-corrosion cracking behavior of stainless steels under different test methods

Chloride-induced stress-corrosion cracking (SCC) is one of the failure modes of stainless steels. Highly alloyed austenitic stainless steels S32654, S31254, and N08028, and duplex grades S32750 and S31803 possess much improved resistance to SCC compared with S30400 and S31600 steels. With the development of a database, SSData, experimental data collected from calcium chloride tests, autoclave tests, and drop evaporation tests were evaluated. Stress-corrosion cracking data generated by autoclave tests agreed well with the practical service conditions and can be used to discriminate alloys for SCC resistance in sodium chloride solution. Drop evaporation test data can be used in situations where evaporation may occur and cyclic loading may be involved. The SCC resistance of alloys under each method increased with increasing molybdenum equivalent Mo + 0.25Cr + 0.1Ni. For a given alloy, the testing result depends on the stress state and environment; different test methods can give different ranking orders concerning SCC resistance. The performance of duplex stainless steels in a chloride-containing environment at higher temperatures was not as good as expected when dynamic loading was involved.     

Degradation of polyethylene terephthalate films in the presence of lubricants for HFC 134a: a critical issue for hermetic motor insulation systems

Earlier studies conducted in the use of sealed tubes with polyalkylene glycol lubricants and polyethylene terephthalete (PET) films revealed that the PET films exhibited embrittlement and (visual) degradation. This led to an investigation of PET embrittlement mechanisms with the new lubricants used with HFC 134a. The lubricants studied were three polypropylene glycols (the monol, the diol and the completely end-capped glycols), pentaerythritol ester and a blend of monol and ester. The effects of moisture content, temperature and lubricant structure were studied. All lubricants in this study were of viscosity grade ISO-32 (150 SUS). The results were compared to PET film embrittlement in the presence of CFC 12 and mineral oil. This study reconfirmed the earlier findings that the PET films must be dried to lower than 0.1 wt.% moisture content for use in hermetic systems. This paper discusses the effect of the moisture content of the lubricant and the effect of the lubricant structure on PET films. The dependence of the various mechanisms on temperature is shown. Esters and end-capped polyalkylene glycols are recommended for use with HFC 134a.     

利用电阻场板提高SOI-LIGBT的性能

通过在SOI-LIGBT中引入电阻场板和一个p-MOSFET结构,IGBT的性能得以大幅提高.p-MOSFET的栅信号由电阻场板分压得到.在IGBT关断过程中,p-MOSFET将被开启,作为阳极短路结构起作用,从而使漂移区的过剩载流子迅速消失,IGBT快速关断.而且由于电场受到电阻场板的影响,使得过剩载流子能沿着一个更宽的通道流过漂移区,几乎消去了普通SOI-LIGBT由于衬偏造成的关断的第二阶段.这两个因素使得新结构的关断时间大大减少.在IGBT的开启状态,由于p-MOSFET不导通,因此器件的开启特性几乎与普通器件一致.模拟结果表明,新结构至少能增加25%的耐压,减少65%的关断时间.     

采用轴径向技术有效解决固定床反应器阻力降的快速升高

讨论了固定床反应器阻力降快速升高的原因，介绍了用轴径向技术解决这一问题的原理及优点，及其在铁铬系变换催化剂和钴钼系耐硫变换催化剂反应器中的实际应用。     

微机控制材料试验机的开扰源分析及抗干扰措施

分析和探讨了微机控制材料试验机所受干扰的来源和通道，并采用屏蔽和隔离等一系列措施抑制各种干扰,以达到提高微机控制试验机系统试验结果的可靠性和精确度。     

大型钢制焊接双层低温储罐设计建造

介绍了大型钢制焊接双层低温储罐的结构形式、选材、建造、检验及保冷要求 ,结合所设计的低温液氨储罐 ,对设计建造这类储罐必须考虑的一些问题作了分析