The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Structural integrity in electronics

With continuing miniaturisation, increased performance demands and the requirement to remove lead from solder alloys, the challenges to structural integrity and reliability of electronic equipment are substantial and increasing. This paper outlines typical features in electronic equipment of which the structural integrity community may be generally unaware. Potential failure modes in service are described, and the problems of scale and material characteristics are considered. Progress in the application of fracture mechanics to the life prediction of interconnections is reviewed. The limited evidence available suggests that the crack growth resistance of silver‐containing lead‐free solders is superior to that of the traditional Sn‐37Pb under cycle‐controlled conditions but there is no difference when time‐dependent conditions prevail. In several respects, it is contended that the electronics sector is faced with challenges at least equivalent to those encountered in gas turbines and nuclear power generation.     

弹药内弹道性能检验新方法数学模型的建立

本文对弹药内弹道性能检验的传统方法存在的问题进行了分析,提出了一种新的检验方法,重点对新的检验方法的数学模型的建立过程进行了论述。并对数学模型的精度进行了分析、检验和验证。     

MICROSTRUCTURE AND FATIGUE PROPERTIES OF A WELDED DUPLEX STAINLESS STEEL

Abstract— In response to the increasing structural applications in duplex steels for welded structures, fatigue behaviour of a SAF 2304 grade duplex stainless steel was investigated, considering both the base metal and GTAW welded joints. Fatigue curves and fatigue limits under rotary bending fatigue were obtained. The study focused attention on the microstructural features of fatigue crack propagation of the two series of experiments, thereby permitting an evaluation of the tortuous crack path of welded joints and the mechanisms related to threshold microstructural barriers.     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.     

高装填密度装药技术中的选药计算

本文围绕叠片药这一装药技术,对某炮进行了有关选药计算,研究了制式火药与叠片药之间的弧厚配比和质量配比关系,并得出了一些有实用价值的结论.     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

Fatigue crack growth analysis of welded aluminium RHS T-joints with manipulated residual stress level

The fatigue life of a welded aluminium T‐joint made from beams with rectangular hollow section (RHS) has been predicted using a crack propagation analysis and compared with experimental results from joints with different residual stress levels. To include the effect of the residual stresses, the stress ratio was calculated at the weld toe and, via Walker's equation, introduced into the analysis. How to obtain the Walker exponent has been discussed in detail. The introduction of a stress ratio at the weld toe provides good agreement between the experimentally and analytically found S–N curves. The effect of the residual stress was successfully included in the analysis.     

企业内部公关与企业形象塑造

良好的企业形象是竞争取胜的利器，内部公关是塑造良好企业形象的根本手段。本文阐述了企业内部公关对塑造良好企业形象的重要意义，探讨了实施内部公关的主要途径。