Study on diffusion welding SiCp/ZL101 with Cu interlayer

Through the vacuum diffusion welding SiCp/ZL101 aluminum with Cu interlayer,the effect of welding parame-ter and the thickness of Cu on the welded joint property was investigated,and the optimal welding parameters were putforward at the same time.The microstructure of joint was analyzed by means of optical-microscope,scanning electron mi-croscope in order to study the relationship between the macro-properties of joint and the microstructure.The results showthat diffusion welding with Cu interlayer could be used for welding aluminum matrix composites SiCp/ZL101 successfully.     

接触疲劳过程中的诱发相变和冷作硬化SCIEI

研究了三种丝杠钢的接触疲劳性能。利用TEM和背散射Mossbauer谱研究了三种钢在接触疲劳前后的显微组织结构;测量了接触区中心线下显微硬度随层深的变化。结果表明:接触应力诱发A_R→M相变,并导致一定深度的冷作硬化。讨论了诱发相变和冷作硬化对接触疲劳性能的影响。     

斜压状态下托轮滚圈多体接触的力学特征

根据滚圈处筒体的变形及力平衡条件,建立了计算滚圈与筒体间接触压力分布的数学模型。研究了斜压状态下托轮滚圈多体接触模型的特点,开发了斜压接触下托轮滚圈有限元建模程序,该程序适用于任何载荷、载荷比、偏斜角下托轮滚圈的接触有限元分析。应用均匀设计法,设计了托轮与滚圈多体接触的有限元计算方案,通过计算,得出了托轮与滚圈的应力及变形情况。通过对滚圈的变形椭圆度和内、外表面的最大等效应力进行多元线性回归,得到了滚圈的变形椭圆度和内、外表面的最大等效应力随支承载荷、载荷比、托轮偏斜角的变化公式。     

粗粒料三轴试验橡皮膜嵌入量数值模拟

在粗粒料三轴试验中,橡皮膜嵌入量可造成显著的体积变形量测误差。本文针对颗粒材料的接触特点,利用Nagata Patch方法重建颗粒表面,基于重建曲面进行接触状态的判断和接触几何信息的计算,开发了高效的颗粒接触算法。该法采用dual mortar有限元方法处理颗粒与橡皮膜间的接触模拟,针对橡皮膜变形较大的特点,采用更新坐标的大变形计算格式,并根据重建的颗粒表面对颗粒-橡皮膜的距离进行几何修正,实现了颗粒-橡皮膜接触的精细化模拟,可较好地模拟计算“柔性”橡皮膜嵌入颗粒孔隙的过程。进行了Kramer钢球试验以及粗颗粒料和标准粗砂三轴试验橡皮膜嵌入过程的模拟计算,计算结果符合一般规律,与相应的试验结果吻合较好,验证了本文方法对于粗粒料膜嵌入问题的适用性。     

pHEMA: An Overview for Biomedical Applications

Poly(2-hydroxyethyl methacrylate) (pHEMA) as a biomaterial with excellent biocompatibility and cytocompatibility elicits a minimal immunological response from host tissue making it desirable for different biomedical applications. This article seeks to provide an in-depth overview of the properties and biomedical applications of pHEMA for bone tissue regeneration, wound healing, cancer therapy (stimuli and non-stimuli responsive systems), and ophthalmic applications (contact lenses and ocular drug delivery). As this polymer has been widely applied in ophthalmic applications, a specific consideration has been devoted to this field. Pure pHEMA does not possess antimicrobial properties and the site where the biomedical device is employed may be susceptible to microbial infections. Therefore, antimicrobial strategies such as the use of silver nanoparticles, antibiotics, and antimicrobial agents can be utilized to protect against infections. Therefore, the antimicrobial strategies besides the drug delivery applications of pHEMA were covered. With continuous research and advancement in science and technology, the outlook of pHEMA is promising as it will most certainly be utilized in more biomedical applications in the near future. The aim of this review was to bring together state-of-the-art research on pHEMA and their applications.     

LF软吹时间对硅脱氧弹簧钢氧化物夹杂控制影响

 对于一些采用硅锰脱氧冶炼工艺的特殊钢,为保证钢水洁净度,常会选择较长时间的LF软吹处理,导致过程能耗增加。通过工业试验,借助FEI Explorer 4自动扫描电镜检测,研究不同LF精炼软吹时间对硅脱氧弹簧钢55SiCr铸坯氧化物夹杂成分、数量的影响;并采用夹杂物极值统计法,对比评价不同LF精炼软吹时间对应成品盘条横截面最大夹杂物尺寸控制情况。结果表明,在LF软吹10 min与软吹40 min 两种工艺条件下,铸坯中尺寸大于5 μm的氧化物夹杂成分接近,均在CaO-SiO₂-Al₂O₃相图中假硅灰石、钙长石和钙铝黄长石共晶低熔点区,其中软吹10 min工艺铸坯氧化物夹杂组成落入低熔点区的数量所占比例更大。LF软吹10 min与软吹40 min铸坯中尺寸大于5 μm的氧化物夹杂数量密度分别为11.70个/100 mm2和14.59个/100 mm2,尺寸大于15 μm 的氧化物夹杂数量密度分别为0.53个/100 mm2和1.65个/100 mm2,LF软吹10 min工艺铸坯大尺寸氧化物夹杂数量密度略低于LF软吹40 min工艺。当预测面积为30 000 mm2时,两种LF软吹时间对应成品盘条横截面最大夹杂物尺寸分别为27.1 μm和28.1 μm,盘条最大夹杂物尺寸控制无显著差别。结合硅锰脱氧钢中大尺寸低熔点CaO-SiO₂-Al₂O₃系夹杂物主要源自钢包渣乳化卷入,具有与钢水和氩气泡界面接触角很小、难以通过吹氩上浮去除的特点,建议硅锰脱氧钢LF软吹过程按短时间快节奏进行控制。     

用圆柱铣刀加工带冠弯扭叶片

本文把微分几何中曲线与曲面之间的“切触”概念应用于叶片复杂曲面的数控加工，提出用圆柱铣刀的外圆在五坐标联动中加工小曲率曲面的最佳切触条件。     

Dressing of filigree fine-grained metal bonded grinding wheels

Metal bonded grinding tools offer a remarkable potential for micro grinding because of their favorable wear behavior. However, metal bonded grinding tools, especially dicing blades, are hard to dress by conventional dressing methods. Electro contact discharge dressing, which is presented in this paper, is a numerically controlled dressing process offering the possibility to create the geometry and topography of the grinding wheel simultaneously at negligible dressing forces. The power of an electric circuit thermally removes the metal bond of the grinding wheel during the dressing process. The quality of the created profiles and the influence of the dressing parameters on the specific material removal rate of the grinding tool as well as the wear of the electrode are investigated at fine-grained grinding wheels.     

固液挤压下陶瓷粒子增强铝基复合材料组织特点及其形成机制

本文使用接触反应法制备ＴｉＣｐ／ＬＹ１２复合材料熔体，然后经固液挤压直接制取复合板材与棒材。使用背散射扫描电镜对Ｔ６处理后的复合板材组织特点进行观察，揭示了颗粒的分布特征、基体组织特点及其成因。