滚子齿式空间分度凸轮机构的研究

本文以微分几何和空间旋转矩阵算子理论为数学工具,应用空间曲面啮合原理,对滚子齿式空间分度凸轮机构进行了系统的研究。推导了凸轮轮廓曲面方程、啮合方程和压力角计算公式,并对凸轮曲面的曲率进行了分析,给出了主曲率、诱导主曲率等一系列计算公式,最后给出了凸轮工作曲面产生根切的判别条件。     

双链轮间歇运动机构分析

本文讨论了双链轮间歇运动机构的工作原理、运动分析、运动参数和特性.     

基于嵌入式Linux技术的间歇式染色机控制器的研究

针对传统间歇式控制器在联网、人机交互、染程编辑、控制运算等功能上的不足,提出基于嵌入式Linux技术的间歇式染机控制器方案,并采用开发源代码免费嵌入式Linux系统eCos,在PC/104硬件平台上进行了实现.     

地温可恢复性对土壤源热泵运行的影响

在地源热泵运行过程中,利用间歇过程,弥补土壤传热慢的缺陷。土壤源热泵间歇运行时间可以改变土壤温度的变化规律,增强传热并实现更佳的热泵运行工况。实验是在冬季运行工况下进行的,着重对间歇运行条件下地温变化趋势进行研究。     

循环间歇溅射工艺对PLT薄膜性能的影响

采用射频磁控溅射技术利用循环间歇溅射工艺,在Pt/Ti/SiO2/Si基片上制备出了镧钛酸铅(PLT)薄膜。通过原子力显微镜、X-射线衍射仪分析了循环间歇溅射工艺对薄膜形貌、结构和铁电性能的影响。实验结果表明,相比于连续溅射工艺,循环间歇溅射工艺的基片温度较低,且制得的PLT薄膜晶粒细小、均匀,结构致密。薄膜具有纯钙钛矿型结构,循环次数从1次增加到3次,其(100)和(200)峰衍射强度逐渐增强,结晶性提高,铁电性能逐渐增强,其饱和极化强度由28μC/cm2增大到53μC/cm2,剩余极化强度由5μC/cm2增大到12μC/cm2。循环4次溅射后,薄膜的结晶性和铁电性开始下降。     

预制桩及搅拌桩在东溪水闸加固中的应用

通过对东溪水闸闸室地基强度的验算及对地基表层抗滑移定及深层抗滑稳定的分析，提出了采用预制桩及搅拌桩抗滑墙除险加固闸基的办法，此方法在满足安全的前提下，可节省投资，缩短工期，为闸基稳定加固处理提供了借鉴的经验。     

一次盐水精制工艺操作条件的研究

对石灰-碳酸铵法精制一次盐水的工艺操作条件、特别是对搅拌因素的影响作了研究,得出最好的操作条件为:加灰一级搅拌,速度梯度值1400S~(-1),搅拌时间15S,二、三级搅拌共10min,速度梯度值.750S~(-1),絮凝剂加入搅拌,速度梯度550S~(-1),搅拌时间6S,在此条件下,500ml 量筒试验,5min 时澄清液,其浊度为5PPM 左右。     

Diagnosis of Intermittent Faults

The diagnosis of intermittent faults in dynamic systems modeled as discrete event systems is considered. In many systems, faulty behavior often occurs intermittently, with fault events followed by corresponding reset events for these faults, followed by new occurrences of fault events, and so forth. Since these events are usually unobservable, it is necessary to develop diagnostic methodologies for intermittent faults. Prior methodologies for detection and isolation of permanent faults are no longer adequate in the context of intermittent faults, since they do not account explicitly for the dynamic behavior of these faults. This paper addresses this issue by: (i) proposing a modeling methodology for discrete event systems with intermittent faults; (ii) introducing new notions of diagnosability associated with fault and reset events; and (iii) developing necessary and sufficient conditions, in terms of the system model and the set of observable events, for these notions of diagnosability. The definitions of diagnosability are complementary and capture desired objectives regarding the detection and identification of faults, resets, and the current system status (namely, is the fault present or absent). The associated necessary and sufficient conditions are based upon the technique of diagnosers introduced in earlier work, albeit the structure of the diagnosers needs to be enhanced to capture the dynamic nature of faults in the system model. The diagnosability conditions are verifiable in polynomial time in the number of states of the diagnosers.     

Experimental Modelling using Low Melting Point Metallic Melts: Relevance for Metallurgical Engineering

This paper describes model experiments with liquid metals of low melting point as an important tool to investigate the flow structure and related transport processes in melt flows being relevant for metallurgical applications. Three examples have been selected to demonstrate the benefit of such experiments, namely the electromagnetic stirring of a metallic melt in a pool, the directional solidification of Al‐Si alloys under the influence of an electromagnetically driven flow and the behaviour of a liquid metal bubble plume if a vertically travelling field is applied. Results of flow measurements are presented and the relevance for metallurgical processes is discussed.