Dose and dose rate effects on coherent-to-incoherent transition of precipitates upon irradiation

A typical precipitation hardened alloy, Cu-Co dilute alloy was selected to study the precipitation behavior and irradiation effect on precipitates. It is found that the principal effect of ion irradiation on the coherent precipitates is loss of coherency, and TEM cross-section observations show that the fraction of the incoherent precipitates is dependent on dose but not on dose rate during heavy ion irradiation.     

辐照损伤对锆合金电化学性能的影响

综述了堆内辐照对锆合金电化学性能影响的概况，浅析了堆内辐照损伤的机理，并重点探讨了主要的堆内辐照源——中子辐照对锆合金微观结构与氧化性能的影响。进一步阐述了堆外离子轰击模拟堆内中子辐照研究方法的进展概况，并就离子轰击实验参量的选择进行了较为深入的分析。     

Effect of annealing treatment on electrochemical property of LiNi0.5Mn1.5O4 spinel

LiNi0.5Mn1.5O4 was prepared under different cooling conditions. The electrochemical properties of LiNi0.5Mn1.5O4 prepared under different cooling conditions were investigated. The results show that LiNi0.5Mn1.5O4 synthesized with or without annealing treatment has similar X-ray diffraction patterns that can be indexed to cubic spinel structure. The mass loss occurring above 650℃ during the heating process can be mostly gained during the cooling process. LiNi0.5Mn1.5O4 synthesized with an annealing treatment exhibits almost one voltage plateau at around 4.7 V and higher capacity with a quick fading upon cycling, whereas LiNi0.5Mn1.5O4 synthesized without annealing treatment shows two voltage plateaus at around 4.1 and 4.7 V and superior capacity retention upon cycling both at rates of 1/7C and 1 C, though the capacity is not high.     

Synthesis and electrochemical properties of Th-doped LiMn2O4 powders for lithium-ion batteries

To improve the cycle performance of eco-friendly and cost-effective spinel LiMN2O4 as the Li secondary batteries, the Th-doped LiThxMn1-xO4 spinel powers were synthesized by solid-state method. The starting materials, Li2CO3,MnO2 and Th(NO3)4·4H2O, were mixed uniformly using a traditional ball milling, which resulted in a uniform particle size distribution in the mixed powers. Tests of X-ray diffraction, SEM, impedance spectra and charge-discharge were carried out for LiThxMn1-xO4 cathode materials. Results show that the synthesized LiTh0.01Mn1.99O4 material exhibits standard spinel structure, regular particle morphology and excellent property of charge-discharge for big current. The capacity retention of the material modified by doping Th is more than 85.1% of the first discharge specific capacity of 111.5 mAh·g -1 after 20 cycles at the current rate 1C, while the pristine LiMN2O4 is only 57% of the first discharge specific capacity of 110.2 mAh·g-1 after the same cycles at the same current rate.     

40CrNiMo钢形变离子注入复合强化机理研究

对40CrNiMo钢施行形变离子注入复合强化处理工艺,通过对未处理件、形变强化处理件、离子注入件及形变与离子注入复合强化处理件的表面显微硬度、残余应力、摩擦磨损等性能的分析和比较,探讨形变离子注入的强化机理及最佳工艺参数。结果表明,经上述各种处理后,显微硬度和耐磨性均有所提高,其中形变与离子注入复合处理后的效果更为明显。分析表明,表层硬相化合物的形成及晶粒细化是材料表面耐磨性提高的主要原因,残余应力的增加提高了抗疲劳性。     

环氧玻璃鳞片树脂防腐技术在阳离子交换器上的应用

本文介绍了环氧玻璃树脂鳞片技术在现场防腐中的应用，采用了新型冷法解决防腐问题，有助于彻底改变衬胶防腐衬里局部修补难度大的问题，是解决局部防腐的良好途径。     

The effect of niobium ion implantation on the oxidation behavior of aγ-TiAl-based intermetallic

The effect of niobium implantation (2×10¹⁶ and 10¹⁷ ions/cm²) on the oxidation behavior of a -TiAl-based intermetallic alloy Ti–48Al–2Cr in air at 800°C has been examined. Isothermal studies with exposure times up to 200 hr and cyclic-oxidation tests up to 800 hr revealed a negligible effect for the low implantation dose. However, a remarkable decrease in oxidation rates was observed for the material implanted with 10¹⁷ Nb ions/cm². The improvement in the oxidation resistance appeared to be similar to that obtained by alloying of the intermetallic with a few atomic percent niobium. Possible mechanisms for the effect of niobium on the oxidation resistance of TiAl-base intermetallics are discussed in view of the results obtained for the implanted material.     

溶解和离子交换反应中K+的快速测定

离子溶液中快速传递及反应动力学过程的跟踪研究在实验上较为困难 ,为此基于离子选择性电极建立溶液中离子活度即时采集系统 ,并结合活度系数模型准确计算离子浓度 .该方法测定速度快 ,最小间隔为 1s,且所得离子浓度最大偏差小于 2 % .用此方法测定了硫酸钾溶解过程以及钛酸钾离子交换反应过程中钾离子浓度的变化 ,获得传统方法难以测定的数分钟内相关动态过程受溶剂、pH值的影响结果 .该方法可推广应用于研究其他各种动态过程 (如溶解、结晶、沉淀、离子交换、吸附和扩散等过程 )     

离子交换树脂非均相催化乙酰化合成乙酰甲胺磷

研究了在间易搅拌釜中以阳离子交换树脂为催化剂，由甲胺磷催化乙酰化合成乙酰甲胺磷。分别考察了不同类型离子交换树脂的催化乙酰化作用。并且研究了搅拌速度，催化剂用量以及反应温度对乙酰化反应的影响。研究结果表明，以NKC9型离子交换树脂在333.15K温度下具有最好的催化乙酰化作用。     

Magneto-sensitive nickel nanowires fabricated by electrodeposition into multi- and single-ion track templates

Polycarbonate templates of (30±1) μm thickness containing cylindrical etched-track nanochannels of (500±50) nm diameter were used for electrodeposition of Ni nanowires. Using 10⁴ channels per cm², the most favourable deposition potential of  − 1.0 V was determined in a potentiostatic mode by varying the deposition potential with respect to an Ag/AgCl reference electrode over a range between  − 0.1 V and  − 1.5 V. The deposition efficiency at  − 1.0 V was estimated around 10%. The resulting single wires had a resistance around 200 Ω and showed an anisotropic magnetoresistance (AMR) effect of 1%, applicable to directionally sensitive magnetic field sensors.