浅谈门式刚架轻型钢结构厂房中抗风柱的设置

通过对抗风柱上下端的节点几种形式进行分析比较,提出建议性的节点连续方式。     

羟基磷灰石涂层人工关节的应用研究

采用人工合成高纯度的羟基磷灰石粉末，喷涂在具有注册证的钛合金和钴铬钼合金人工关节上。通过生物学基础检测、动物实验和临床试用，证明所制作的各种羟基磷灰石涂层人工关节，能诱发骨质生长，起生物固定作用，对治疗丧失功能的骨胳效果甚佳。     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

Analysis of the Ductile Strength of Welds Weakened by Notches in Longitudinally Welded Pipes of Large Diameter by the Method of Slip Lines

We study the stressed state of an inhomogeneous welded joint containing an interlayer of a more high-strength material under the action of tensile loads. It is assumed that the contact boundary has a cracklike defect. We deduce analytic dependences of the fracture load on the mechanical inhomogeneity of the joint, thickness of the interlayer, and depth of the defect. The maximum depth of the defect to which the joint is insensitive is established. The proposed theoretical results are innovative and agree with the experimental data obtained for specimens cut out from a pipe of 14KhGS steel.     

Damage mechanism in weldment of 2.25Cr-1Mo steel under creep-fatigue loading

The purpose of this study is to clarify damage process of “Type IV cracking” in weldment of a 2.25Cr-1Mo steel and to propose a micro damage prediction method. From continuous observation under a creep-fatigue test, it was found that spherical shape voids initiated and grew on grain boundaries in fine grain region and these voids grow continuously by changing their shape to crack-like. Both spherical and crack-like void growth rate equations were derived from the proposed void growth model. It was indicated that measured void growth rate under the creep-fatigue loading was well predicted by the growth rate equations.     

VRDS装置常压分馏塔系统的问题分析

胜利炼油厂重油加氢 (VRDS)装置的常压分馏塔为填料塔 ,2 0 0 1年检修开工后该系统出现异常 ,经过查找分析 ,确定轻烃 /产品减压渣油换热器和柴油汽提塔重沸器内漏是装置异常的主要原因     

The stiffness matrix in elastically articulated rigid-body systems

Discussed in this paper is the Cartesian stiffness matrix, which recently has received special attention within the robotics research community. Stiffness is a fundamental concept in mechanics; its representation in mechanical systems whose potential energy is describable by a finite set of generalized coordinates takes the form of a square matrix that is known to be, moreover, symmetric and positive-definite or, at least, semi-definite. We attempt to elucidate in this paper the notion of “asymmetric stiffness matrices”. In doing so, we show that to qualify for a stiffness matrix, the matrix should be symmetric and either positive semi-definite or positive-definite. We derive the conditions under which a matrix mapping small-amplitude displacement screws into elastic wrenches fails to be symmetric. From the discussion, it should be apparent that the asymmetric matrix thus derived cannot be, properly speaking, a stiffness matrix. The concept is illustrated with an example.     

厚断面球铁的声速

论述了影响厚断面球铁声速和声波衰减的各种因素。指出，必须在应力状态下同时考核声速和声波衰减，以作为判别厚断面球铁材质的一种手段。     

配极变换及其在求解锥面截交线中的应用

本文应用配极变换的几何性质来确定锥面截交线的中心及其主要轴线，这对于准确地绘制或使用数控绘图机来绘制二次曲线．是很有意义的．     

钻杆接头螺纹退刀尺寸对接头寿命的影响

钻杆接头螺纹退刀尺寸是指外螺纹接头的台肩面到螺纹消失前第一个完整螺纹之间的距离。GB9253．1－88规定退刀尺寸应小于或等于12．7mm内螺纹，钻杆接头内螺纹的锤孔尺寸为16±2mm，以保证内、外螺纹啮合良好。经检测发现，从日本NKK公司进口的所有φ127mm钻杆接头外螺纹退刀尺寸都大于12．7mm，镗孔尺寸为16～18mm。而APISpec7K规定钻杆接头内螺纹最小镗孔尺寸为15．9mm。鉴于此，建议对我国的有关标准作相应修改，与API标准保持一致。