等离子体横向刻蚀硅的特性研究

研究了用SiO2 +Al作掩模 ,SF6 +O2 混合气体等离子体对Si的横向刻蚀 ,其结果表明 ,在SF6 +O2 等离子体气氛中 ,Al是很好的保护膜 ,可以在待悬浮器件下形成大的开孔。因此 ,预计用这种技术 ,可以在Si片上集成横向尺寸为数百微米 ,具有优良高频性能的MEMSRF/MW无源器件 ,如开关、传输线、电感和电容等。     

船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

储层横向相变对剩余油分布的影响

处在构造边部、低部位的商５－５井，在改注水井排液中发现不含水的高产这种非常规现象，由此引起对地质因素的分析。浅湖相沉积的主体是滩砂微相，它可细分为“滩脊”和“滩侧”，其中“滩脊”砂体的泥质含量低，孔隙度、渗透率都较高，而“滩侧”则泥质含量高，物性差。在从“滩脊”砂体向“滩侧”过渡时，极易形成类似于砂体尖灭的岩性封堵，造成剩余油富集，而“滩脊”不一定就在构造的高部位。陆相沉积的砂体非均质性很强，孔隙度和渗透率在横向上的变化很大，高部位的油层水淹，低部位的油层不一定就高含水，这是因为砂体横向上的非均质性，使同一时间单元沉积的砂体很可能不连通。基于这些分析，地质工作者不妨运用沉积微相的原理在构造的低部位或边部寻找剩余油富集区，商５－５井的现实给了我们很好的启示。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

结构化P2P网络中基于流言传播的负载均衡

提出了结构化P2P网络中利用结点间周期性的拓扑维护通信来夹带、传播消息进行负载均衡的方法，具体针对Chord系统从消息传播的速度和规模两个方面分析了该方法的性能，并利用仿真进行了验证。讨论了结论在其它形式网络中的推广和实现中的消息管理问题。     

Cyclic strength of parts with overlapping zones formed by roller burnishing

The authors study residual stresses in and cyclic strength of shaft with overlapping zones formed during roller burnishing. The most significant decrease in fatigue strength is shown to occur in the presence of an overlapping zone with the areas arising due to a lowered roller burnishing pressure in the second pass. __________ Translated from Problemy Prochnosti, No. 3, pp. 144–148, May–June, 2006.     

带有块间串扰MC-CDMA的时域信道估计和多用户检测

本文把带有IBI的MC-CDMA系统等效解释为特殊的直接序列码分多址（DS-CDMA）系统，并给出了相应的时域信道估计方法和时域线性最小均方误差（MMSE）多用户检测方法。仿真实验表明了本文方法的性能。