A Bluetooth Based Sensor Network for Civil Infrastructure Health Monitoring

Communicating with sensors has long been limited either to wired connections or to proprietary wireless communication protocols. Using a ubiquitous and inexpensive wireless communication technology to create Sensor Area Networks (SANs) will accelerate the extensive deployment of sensor technology. Bluetooth, an emerging, worldwide standard for inexpensive, local wireless communication is a viable choice for SANs because of its inherent support for some of the important requirements – low power, small form factor, low cost and sufficient communication range. In this paper we outline an approach, centered on the Bluetooth technology, to support a sensor network composed of fixed wireless sensors for health monitoring of highways, bridges and other civil infrastructures. We present a topology formation scheme that not only takes into account the traffic generated by different sensors but also the associated link strengths, buffer capacities and energy availability. The algorithm makes no particular assumptions as to the placement of nodes, and not all nodes need to be in radio proximity of each other. The output is a tree shaped scatternet rooted at the sensor hub (data logger) that is balanced in terms of traffic carried on each of the links. We also analyze the scheduling, routing and healing aspects of the resulting sensor-net topology.     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

小波变换在光谱特征提取方面的应用

人们在处理高光谱图像时一般要对一些典型地物进行光谱分析、特征波段的提取,以便提取出最大量的有效信息,剔除无用或冗余的信息,然后再进行分类识别.采用小波变换的分析方法,选用合适的小波进行分解,根据分解后的高频分量中包含的重要信息,利用局部相邻的正负极值点找出对应于原始光谱曲线上每个吸收带的左右边界;利用局部过零点,即可比较精确的提取出各个吸收带的中心波长.该方法比传统的光谱特征提取方法更简洁、有效,实验证明为一种比较理想的光谱特征提取方法.     

WPAN/WLAN应用环境下基于PER的链路自适应算法

本文重点研究基于包错误率测量的链路自适应算法，分析了包错误率与信道参数的关系，提出了一种有别于固定门限值方案的优化门限值方案。仿真结果表明，优化门限值方案的网络吞吐量要大于固定门限值方案和基于信干比估计的链路自适应算法，最大增幅可达12Mbit/s。在系统引入重传机制后，网络吞吐量将有所损失，但最大不超过1Mbit/s，相比较服务质量的提高是值得的。需指出的是，虽然分析和仿真均以HIPERLAN／2为例，但不失一般性，它们同样适合于WPAN/WLAN等类似系统。     

Quality Control for Scalable Media Processing Applications

Many media processing applications create a load that varies significantly over time. Hence, if such an application is assigned a lower processing-time budget than needed in its worst-case load situation, deadline misses are likely to occur. This problem can be dealt with by designing media processing applications in a scalable fashion. A scalable media processing application can run in multiple qualities, leading to correspondingly different resource demands. The problem we consider is to find an accompanying quality control strategy, which minimizes both the number of deadline misses and the number of quality changes, while maximizing the quality of processing. We present an initial approach to the above problem by modeling it as a Markov decision process (MDP). Our model is based on measuring relative progress at milestones. Solving the MDP results in a quality control strategy that can be applied during runtime with only little overhead. We evaluate our approach by means of a practical example, which concerns a scalable MPEG-2 decoder.     

烟气轮机叶片应力分析与寿命评估方法评述

烟气轮机是炼油厂催化裂化装置的关键设备,合理预测叶片疲劳寿命是保障烟机安全运行的有效手段。从力学建模和边界条件两个方面简要阐述了叶片的应力分析方法,并系统分析了影响烟机叶片疲劳寿命的主要因素,提出了利用改进的局部应力应变法进行叶片寿命预测的合理性和叶片疲劳寿命的评估方法。     

现役水工钢闸门结构可靠性鉴定时荷载取值分析

采用类比法确定现役水工钢闸门结构的荷载评估基准期。以静水压力为例，得了其在荷载评估基准期内的统计参数，讨论了闸门主梁受弯碱坏时可靠指标随继续使用期的变化。     

挤扩支盘桩在湿陷性黄土地基中的应用

湿陷性黄土具有遇水发生湿陷、承载力大幅度降低的性质,这种性质直接影响到基础的承载力。为了研究支盘桩在湿陷性黄土地基中的承载性状,对湿陷性黄土中的3根支盘桩进行预浸水静载荷试验,结果表明,支盘桩荷载—沉降曲线为缓变型,具有较好的承载性能,荷载传递规律与在非湿陷性黄土地基中具有相似的性质,桩身各段承载力的发挥具有明显的顺序性,其结果为挤扩支盘桩在湿陷性黄土地基中的应用提供了依据。     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.