Polyethylene oxide-polypropylene oxide -polyethylene oxide derived porous carbon materials with different molecular weights as ORR catalyst in alkaline electrolytes

Polyethylene oxide (PEO)-polypropylene oxide (PPO)-polyethylene oxide block copolymer having different molecular weights are used as precursors of carbon materials to prepare Hollow -Derivatives carbon material as an electrocatalyst through block copolymer self-assembly. The composition and microstructure of the prepared catalysts are shown by Raman spectroscopy, X-ray diffraction (XRD), Test of nitrogen adsorption and desorption curves, High resolution transmission electron microscopy (HR-TEM) and scanning electron microscopy (HR-SEM). Oxygen was passed into alkaline electrolyte solution until the solution reached saturation state. With molecular weight increasing, the obtained sample gradually changed from block to hollow and spherical. When the molecular weight was 12600 g mol^?1, the evenly hollow carbon nanocages was acquired (C-12600). In O₂ saturated alkaline electrolyte (0.1 M KOH solution), C-12600's limited current density，half-wave potential and initial potential are 5.23 mA cm^?2@0.4 V, 0.72 V and 0.81 V, respectively. And most important is that half-wave potential and onset potential have barely change after 2000 cycles of cyclic voltammetry. As a result, the porous carbon materials exhibited excellent electrocatalytic activity while maintaining high stability in alkaline KOH solution.     

Study of the synergistic effect of boron nitride and carbon nanotubes in the improvement of thermal conductivity of epoxy composites

The enhancement of the thermal conductivity, keeping the electrical insulation, of epoxy thermosets through the addition of pristine and oxidized carbon nanotubes (CNTs) and microplatelets of boron nitride (BN) was studied. Two different epoxy resins were selected: a cycloaliphatic (ECC) epoxy resin and a glycidylic (DGEBA) epoxy resin. The characteristics of the composites prepared were evaluated and compared in terms of thermal, thermomechanical, rheological and electrical properties. Two different dispersion methods were used in the addition of pristine and oxidized CNTs depending on the type of epoxy resin used. Slight changes in the kinetics of the curing reaction were observed in the presence of the fillers. The addition of pristine CNTs led to a greater enhancement of the mechanical properties of the ECC composite whereas the oxidized CNTs presented a greater effect in the DGEBA matrix. The addition of CNTs alone led to a marked decrease of the electrical resistivity of the composites. Nevertheless, in the presence of BN, which is an electrically insulating material, it was possible to increase the proportion of pristine CNTs to 0.25 wt% in the formulation without deterioration of the electrical resistivity. A small but significant synergic effect was determined when both fillers were added together. Improvements of about 750% and 400% in thermal conductivity were obtained in comparison to the neat epoxy matrix for the ECC and DGEBA composites, respectively. © 2019 Society of Chemical Industry     

Two-step pyrolytic engineering to form porous nitrogen-rich carbons with a 3D network structure for Zn-air battery oxygen reduction electrocatalysis

It is of great urgency to design inexpensive and high-performance oxygen reduction reaction (ORR) electrocatalysts derived from biowastes as substitutes for Pt-based materials in electrochemical energy-conversion devices. Here we propose a strategy to synthesize three-dimensional (3D) porous nitrogen-doped network carbons to catalyze the ORR from two-step pyrolysis engineering of biowaste scale combined with the use of a ZnCl₂ activator and a FeCl₂ promotor. Electrochemical tests show that the synthesized network carbons have exhibited comparable ORR catalytic activity with a half-wave potential (~0.85 V vs. RHE) and outstanding cyclical stability in comparison to the Pt/C catalyst. Beyond that, a high electron transfer number (~3.8) and a low peroxide yield (<7.6%) can be obtained, indicating a four-electron reaction pathway. The maximum power density is ~68 mW cm^?2, but continuous discharge curves (at a constant potential of ~1.30 V) for 12 h are not obviously declined in Zn-air battery tests using synthesized network carbons as the cathodic catalyst. The formation of 3D porous structures with high BET surface area can effectively expose the surface catalytic sites and promote mass transportation to boost the ORR activity. This work may open a new idea to prepare porous carbon-based catalysts for some important reactions in new energy devices.     

基于新型光纤的传输技术探讨

随着互联网的高速发展，引发了网络流量、电信骨干网流量急速增长，使得网络容量的提升迫在眉睫。目前，100G 系统已经商用，超100G系统能够更有效地解决流量和网络带宽持续增长带来的压力，本文主要介绍新型单模光纤的特性以及探讨基于新型单模光纤的传输技术。     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Two-step method to deposit ZrO2 coating on carbon fiber: Preparation,characterization, and performance in SiC composites

Recently, ceramic matrix composites reinforced by short carbon fibers (CFs) attracted increasing attentions. To further improve mechanical properties and oxidation resistances, CFs were subjected to oxidation and acidification followed by sol-gel dip-coating to deposit ZrO₂ on their surfaces. ZrO₂-C_f/SiC composites were fabricated by joint hot compression molding and sintering, compared to C_f/SiC and SiC prepared by the same method. Microstructural analyses indicated that ZrO₂ coatings were successfully deposited on CF surfaces, formed strong bonding and interfaces between CF and the matrix. Meanwhile, CFs were found uniformly distributed in SiC matrix with random orientations. Flexural curves of ZrO₂-C_f/SiC and C_f/SiC revealed the presence of “false plasticity” regions after sharp drops, which were quite different from brittle flexural behavior of SiC ceramic. Compression strength of the three samples showed step-up growth. ZrO₂-C_f/SiC exhibited the highest value, indicating the introduction of CFs and ZrO₂ coatings do have great influence on mechanical performances. After heat treatment, ZrO₂-C_f/SiC exhibited better oxidation resistance than C_f/SiC, with weight loss ratios estimated to ??3.76% and ??6.43%, respectively. These improved properties indicated that ZrO₂-C_f/SiC would be excellent alternatives to other existence materials under ultra-high temperature environments.     

Thermoplastic and low dielectric constants polyimides based on BPADA-BAPP

ABSTRACT

The thermoplastic and low dielectric constants polyimides were introduced. The polyimides were prepared by pyromellitic dianhydride (PMDA) or 4,4?-(4,4?-Isopropylidenediphenoxy)diphthalic anhydride (BPADA) as anhydride monomer and 4,4?-oxydianiline (ODA) or 2,2-bis(4-(4-aminephenoxy)phenyl)propane (BAPP) as amine monomer. The polyimides were well characterized by FT-IR, thermogravimetric analysis, dynamic thermomechanical analysis, dielectric measurement, and tensile test. The dielectric constants were 2.32–2.95 compared with 3.10 of ODA-PMDA polyimide, while partly polyimides were thermoplastic. The results indicated anhydride monomers, containing lateral methyl groups, made polyimides become thermoplastic. The results of molecular simulations via Materials Studio also proved this conclusion.     

Synergistic flame retardant effects of activated carbon and molybdenum oxide in poly(vinyl chloride)

The synergistic effects of activated carbon (AC) and molybdenum oxide (MoO₃) in improving the flame retardancy of poly(vinyl chloride) (PVC) were investigated. The effects of AC, MoO₃ and their mixture with a mass ratio of 1:1 on the flame retardancy and smoke suppression properties of PVC were studied using the limiting oxygen index and cone calorimeter tests. It was found that the flame retardancy of the relatively cheaper AC was slightly weaker than that of MoO₃. In addition, the incorporation of AC and MoO₃ greatly reduced the total heat release and improved smoke suppressant property of PVC composites. When the total content of AC and MoO₃ was 10 phr, PVC/AC/MoO₃ had the lowest peak heat release rate and peak smoke production rate values of 173.80 kW m^?2 and 0.1472 m² s^?1, which represented reductions of 47.3 and 59.9%, respectively, compared with those of PVC. Furthermore, thermogravimetric analysis and gel content tests were used to analyze the flame retardant mechanism of AC and MoO₃, with results showing that AC could promote early crosslinking in PVC. Char residue left after heating at 500 °C was analyzed using scanning electron microscopy and Raman spectroscopy, and the results showed that MoO₃ produced the most compact char, with the smallest and most organized carbonaceous microstructures. © 2017 Society of Chemical Industry