改性纤维素增强丙烯酰胺水凝胶的合成与拉伸性能研究

采用水媒法制备了低取代度羧甲基纤维素,并用接枝聚合法制备了改性纤维素/丙烯酰胺水凝胶,考察了单体质量比、取代度等对水凝胶拉伸性能的影响.结果表明:对于接枝聚合反应,采用低取代度羧甲基纤维素可以提高纤维素的有效用量;当交联剂用量为180 mg/L、引发剂1 300 mg/L、低取代度羧甲基纤维素和丙烯酰胺质量比在1∶4 ～ 1∶4.5之间、单体质量分数为30%时,合成水凝胶的拉伸强度达到0.28 MPa;在此基础上,适量添加15%的淀粉可使水凝胶拉伸强度达到0.47 MPa;添加1%二氧化钛可使水凝胶拉伸强度达到0.38 MPa.     

应力吸收层沥青混合料的低温抗裂性能

通过对自主研发的Sampave等3种改性沥青结合料和不同级配的应力吸收层沥青混合料进行低温弯曲和低温蠕变试验,分析沥青结合料和矿料级配对应力吸收层沥青混合料低温抗裂性能的影响.结果表明:自主研发的Sampave特种改性沥青混合料具有优良的低温抗裂性能,但单一改性剂SBR改性沥青并不能达到应力吸收层沥青结合料的性能要求;矿料4.75 mm、0.075 mm筛孔通过率对其低温抗裂性能影响较敏感.     

Pressureless low temperature sintering of nanocrystalline zirconia ceramics via dry powder processing

Pressureless sintering approaches provide a simple avenue to manufacture dense ceramic parts with minimal processing equipment, but current pressureless sintering techniques have yet to demonstrate capabilities of producing dense ceramics while maintaining sub-50 nm grain sizes. Nanocrystalline yttria stablized zirconia ceramics were process from 4 mol% yttria stablized zirconia (4YSZ) nanopowders with a crystallite size of 7.5 nm using dry cold isostatic pressing (CIP) where powders are dried immediately prior to green compact formation and CIP vacuum bagging. It is shown that CIP pressures >75 000 psi (517 MPa) effectively remove pores larger than 100 nm and that pressureless sintering occurs at reduced temperatures for green densities ≥50%. Though the sintering kinetics are shown to be similar to other zirconia nanopowder sintering studies, the small initial crystallize size and reduced sintering temperature allowed densities as high as 97.2%, while retaining a ceramic grain size at or below 40 nm. Produced nanocrystalline 4YSZ ceramics with a grain size of 30.3 nm and a density of 96.3% had Vicker's hardnesses as high as 14.2 GPa and Vicker's indentation fracture resistance of 3.43 MPa·, demonstrating that simple processing approaches can be refined to fabricate nanocrystalline ceramics while maintaining high hardness and indentation fracture resistance.     

一种实时低成本压缩算法的VLSI实现

针对传统视频图像压缩算法时延长和成本高的问题,提出一种新的无损/近无损视频压缩算法。该算法由码率控制器和熵编码器组成,其中码率控制器通过对已有信息进行分析（上下文）来确定当前宏块的可用比特数,然后根据大量实验得出的高效Huffman码表,并结合位平面编码器对残差进行编码。实验结果表明,文中提出的视频图像压缩算法能够工作在300 MHz,吞吐量最差为1.3 pixel/cycle,同时仅用一块120＊720的SRAM来存储上一行像素值,因此很好地解决了时延和成本问题。     

带谐波抑制策略的三电平脉冲整流器仿真研究

以城轨牵引供电系统中网侧变流器为研究对象,根据单相三电平脉冲整流器等效数学模型,应用瞬态电流控制策略,加入中点电位平衡策略,给出控制策略数学模型和控制方程.并根据脉冲整流器低次谐波消除原理,对该控制策略下,加入整理器低次谐波消除策略前后,脉冲整流器网侧和直流侧输入输出状态进行仿真研究.     

500kV断路器因空气压力低告警导致断路器控制保护回路断线分析

针对天生桥换流站500kV三菱断路器因空气压力低告警导致断路器控制保护回路断线这一情况,根据工作站中出现的信号,结合断路器的控制、保护二次回路,对信号及其出现的缘由进行分析,评估断路器控制保护回路断线时,可能出现的安全生产风险,发现目前存在的问题,并对这些问题提出解决方案。     

Effects of silicone oil and polymeric modifiers on the mechanical properties of highly filled LLDPE

The effects of coupling agents, silicone oil, and three types of polymeric modifiers on the mechanical properties of linear low density polyethylene (LLDPE) composites highly filled with aluminium hydroxide [Al(OH)₃] were studied. Polymeric modifiers that contain polar groups, such as silane‐grafted polyethylene (Si‐g‐PE) and acrylic‐acid‐grafted ethylene‐vinyl acetate copolymer (AA‐g‐EVA), improve the mechanical properties dramatically, while nonpolar modifiers improve them to some extent. When Al(OH)₃ was treated using a titanate coupling agent, the silicone oil increased the impact strength and elongation at break of the LLDPE/Al(OH)₃ composites. Introduction of a polymeric modifier containing polar groups destroys the beneficial effects of silicone oil on film mechanical properties, while the introduction of a nonpolar elastomeric polymeric modifier retains the high impact strength and elongation at break. SEM analyses provide the indirect evidence of the encapsulation of silicone oil around the filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 121–128, 2002     

Thermal expansion of an SiC particle-reinforced aluminum composite

Using a push-rod dilatometer, we measured between 76 and 390 K the thermal expansion of a particle-reinforced-composite wrought plate obtained by powdermetallurgy methods. The particles, 30% by volume, consisted of monocrystals of -SiC with sizes near 10 m. The matrix consisted of a 6061 aluminum alloy with original particle sizes near 20 m. We found the perpendicular thermal expansivity, ₃, higher by 26% than the in-plane thermal expansivity, ₁-₂. These values differ from a rule-of-mixture prediction by –3 and –23%, respectively. All three _i, components lie outside the Rosen-Hashin bounds. Levin's isotropic model agrees within 10% with the ₁-₂-₃ average. Both the anisotropy and the bounds violation result from microstructural nonhomogeneity arising from processing. Rosen and Hashin's transverse-isotropicsymmetry relationships account approximately for these effects by introducing the anisotropic elastic constants. Using neutron diffraction, we determined that the SiC particles are textureless.Paper presented at the Tenth International Thermal Expansion Symposium, June 6–7, 1989, Boulder, Colorado, U.S.A.     

Design of a broadband dielectric resonator antenna and its application in low sensitivity frequency beam‐scanning array with wide scanning angle and suppressed sidelobes

In this paper, a broadband dielectric resonator antenna (DRA) with a simple H‐slot feeding structure is proposed. The broad bandwidth (~45%) and uni‐directional radiation enable this DRA suitable to work as a radiation element in the construction of a beam‐scanning array with not only low frequency sensitivity which is important for accurate angle estimation of in‐coming targets, but also a wide scanning range. Moreover, stable coupling coefficients are established around all the above three resonances with respect to its corresponding feeding line, ensuring a low sidelobe level (SLL) across the whole operating frequency range. In order to realize such a DRA, a latticed rectangular structure is utilized to generate the lower two resonances, while the upper resonance is generated by its H‐shaped feeding slot. The shape of the latticed dielectric resonator is also modified according to a 3‐D printed fixing structure for an accurate installation. A 20‐element beam‐scanning prototype is demonstrated and manufactured. The range of scanning angle is from ?36° to +13° within the bandwidth of 10 to 16 GHz, corresponding to a frequency sensitivity of only 122.5 MHz/^o. The achieved SLL are smaller than 19 dB for all scanning beams. The above performance indicates that, this array is very suitable for near‐range radar systems requiring an accurate angle estimation.     

IETCAM:基于信息熵的低功耗TCAM分类器

目前,三态内容寻址器被广泛应用于数据平面的高速转发,但现有的索引式TCAM在降低功耗和运行时间等方面仍存在问题.针对这些不足,提出了一种基于信息熵的低功耗索引式TCAM分类器,利用了信息熵技术,有效地解决了规则集在TCAM子块中分布不均、功耗较大的问题.实验表明,在2k大小的规则集下,该算法相较于经典的SmartPC算法平均可以提高63％的功耗降低率,运算时间更新速度缩小了97％,存储开销仅增加了10％.