以YAG为添加剂的气压烧结氮化硅

本文以添加ＹＡＧ的反应烧结氮化硅（ＲＢＳＮ）为前驱体，采用气氛加压烧结的工艺，在０．５～９．０ＭＰａ氮气压力范围，研究了不同氮压对烧结体的密度、相组成、强度和显微结构的影响及其相互间的关系。研究表明，通过改变氮气压力能有效地调控材料的显微结构，材料的性能又受控于显微结构的变化。     

CFRP强度复合Weibull分布的物理特征分析

本文对ＣＦＲＰ材料疲劳后剩余强度的复合Ｗｅｉｂｕｌｌ分布的物理特征进行了初步分析。指出树脂基复合材料失效（破坏）机理的双重性（基体和纤维失效模型）决定了剩余强度（累积损伤程度）测试结果的分布特征。复合Ｗｅｉｂｕｌｌ分布曲线的特征与分析结果对设计、使用及材料研究都有重要参考意义。     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

使用混合杆柱时抽油泵柱塞的超冲程

任何抽油杆柱在理论上都可能产生超冲程，只是大小不同而已。超冲程的存在，使泵柱塞的有效冲程增大，甚至会大于光杆冲程。首次提出了抽油泵柱塞相对超冲程和绝对超冲程的概念，这将有助于正确认识玻璃钢抽油杆的作用和玻璃钢抽油杆的推广使用。将抽油杆柱简化成上端受光杆的激振位移、下端带有集中质量的弹簧－质量力学模型，建立了抽油杆柱纵向振动的偏微分方程和边界条件，然后用固有函数法求解方程，得出了抽油泵柱塞超冲程的无穷级数解析计算式。     

低合金高强度钢的微观组织和疲劳裂纹扩展行为

用透射电镜观察了３０ＣｒＭｎＳｉＮｉ２Ａ钢等温的微观组织，疲劳裂纹扩展行为、裂纹尖端塑性区和位错结构，结果表明，等温状态组织由马氏体和贝氏体组成。在一个奥氏体晶粒内一般存在四个板条领域、裂纹尖端的塑性区内存在主位错带，疲劳断裂的基本组织单元为板条晶或板条束。裂纹遇到板条束界时方向发生较大偏斜。     

Prediction of High-Temperature Long-Term Strength for Damaged Structures

A method is proposed for analytical estimation of the high-temperature long-term strength of structures with material discontinuities, which are stress raisers. We consider the processes involving the formation of diffusion pores. Diffusion processes in metals are strongly enhanced with increasing temperature and stresses.     

柴油机低频排气噪声规律分析

针对柴油机（4－85）低频排气噪声，对其产生机理、规律及其影响因素等作了理论计算、分析及实验。对低频排气噪声信号进行频域分析后可知，其主要由一系列离散的谐波组成，是以柴油机点火频率为基频的一种类周期性噪声，有可能应用有源噪声控制技术。     

火烧油层技术在庙5块低渗透稠油油藏中的应用

方法在物理模拟的基础上，利用数值模拟及油藏工程方法，对影响火烧油层的技术参数进行了优选研究，并对影响火驱成败的油藏地质参数、注气参数进行了分析。目的寻找适合庙５块低渗透稠油油藏的开采方法。结果提出了庙５块火驱的最佳开采方式、点火参数及注气参数；庙５块火驱生产后，平均单井日产液由０１ｔ上升到５６ｔ，平均单井日产油由０１ｔ上升到３５ｔ，生产２６ｄ后由于压风机供风不足被迫停止火驱注气；从数模结果看：火驱最终采收率可达３９８％。结论火烧油层是一种潜力很大的稠油开采方法，但其物理、化学反应机理复杂，火烧前缘难以控制；庙５块火驱初期虽然见到了一定的生产效果，但没有取得经济效益     

莺歌海地区低电阻率气层测井响应特征与判别方法

文中概述了莺歌海地区低电阻率气层的主要测井响应特征,详细分析了低电阻率气层的成因,并提出了测井判别方法.特别强调指出局部发育的菱铁矿对该区地层电阻率无明显影响.     

用废旧橡胶生产精细胶粉的空气涡轮制冷低温粉碎法

利用先进的空气涡轮制冷系统，在低温条件下，将废旧橡胶进行冷冻，粉碎，制成60目以上细度的精细胶粉，此法简称ATCG法，它的冷冻能耗成本仅为国际上通用的液氮法的十分之一，整个工艺过程不产生二次污染，为精细胶粉的制取开辟了一条新途径。