X80焊管H_2S环境应力腐蚀开裂行为研究

采用三点弯曲加载法和微电极扫描测试技术,研究了X80高强度级管线钢及其焊缝区的抗H2S环境应力腐蚀开裂(SSCC)行为。测定了焊接接头的显微硬度分布,分析了显微组织结构、力学性能及抗腐蚀性能之间的相关性。研究表明,热影响区(HAZ)对应力腐蚀开裂最为敏感,母材的纵向和横向取样对应力腐蚀敏感性影响不显著,薄壁管材比厚壁管材有较好的抗H2S环境应力腐蚀性能。HAZ晶粒粗大、硬度高,局部腐蚀倾向大,由此导致该区SSCC敏感性高。     

在糖化酶发酵生产中低温保存黑曲霉菌

在糖化酶生产过程中,为了防止正常生产中黑曲霉菌种性能的变化,对菌种的一级种母进行甘油冷冻保存,在-120℃的条件下分别保存30、60、90d,然后直接接入种母培养基,待成熟后接入种子罐,投入50t发酵罐工业生产,150h左右发酵结束。产酶单位与原工艺条件相一致。     

多功能杀菌剂的合成及其性能研究

在现有季铵盐类杀菌灭藻剂上增加一个脂键，连接一个有机酸基团，合成一种兼具阻垢缓蚀功能的新型工业水处理用杀菌灭藻剂(多功能杀菌剂)，经一系列评价实验表明：新型杀菌剂是较理想的杀菌剂，在较低浓度下，对硫酸盐还原菌(SRB)及腐生菌(TGB)均有很好的杀灭效果，优于1227杀菌剂，同时还具有较好的缓蚀阻垢效果。     

PECVD法低温沉积多晶硅薄膜的研究

在玻璃衬底上采用常规的PKCVD法在低温(≤400℃)条件下制得大颗较(直径＞100nm)、择优取向(220)明显的多晶硅薄膜。选用的反应气体为SiF4和H2混合气体。加入少量的SiH4后，沉积速率提高了近10倍。分析认为，在低温时促使多晶硅结构形成的反应基元应是SiFmHn(m n≤3)，而不可能是SiHn(n≤3)基团。     

模糊层次分析法在腐蚀影响因素分析中的应用

结合国内外对碳钢CO2腐蚀影响因素的研究成果,采用模糊层次分析法对影响输油管道 CO2腐蚀的因素进行定量分析,明确界定出这些因素对二氧化碳腐蚀影响的相对重要性(权重),为后续制定经济有效的管道内腐蚀防护措施提供了客观依据。     

魏氏组织对20#碳钢H2S应力腐蚀开裂性能的影响

文章对H₂S-CO₂-H₂O腐蚀环境下发生H₂S应力腐蚀的20^＃碳钢弯管（无缝钢管）进行了成分、组织、拉伸、硬度和应力腐蚀开裂等性能的试验研究，并与同材质、同时投产、腐蚀环境基本相似而未发生应力腐蚀开裂的在役弯管及未使用的新弯管作对比，结果表明魏氏组织是引起20^＃钢发生应力腐蚀开裂的主要原因；正火能消除魏氏组织，降低钢的应力腐蚀开裂敏感性。     

N-油酰基肌氨酸钠对除盐水缓蚀性能的探讨

对N-油酰基肌氨酸钠单体的缓蚀性能以及与常用除盐水缓蚀剂的协同作用作了探讨,发现在一定浓度下,单体对经过加氨调节后的高温除盐水(氨后除盐水)有良好的缓蚀作用,且与大多数除盐水缓蚀剂有良好的协同效应。在此基础上研制了一种复合药剂,并对其缓蚀、阻蚀性能作了研究。动电位极化曲线扫描图谱表明,该复合药剂属于抑制阳极腐蚀的阳极型缓蚀剂,其适用的水质条件为[Cl~-+SO_4~(2-)]不超过50 mg／L,pH不低于8.0；与阻垢剂复配,可以适用于含Ca~(2+)不超过45 mg／L的水质条件。     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

泡沫夹克管的防水与保温

针对辽河油田应用泡沫夹克管道的情况，从泡沫夹克管的制作和敷设施工直到设计等环节，结合泡沫夹克管防腐保温的机理，并从理论与实践相结合角度出发，提出导致泡沫夹克管腐蚀损坏的最主要原因是管道保温层漏水，进而提出了在设计和施工过程中提高泡沫夹克管质量的措施。     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.