Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

热流法计算高温炉内辐射传热

高温炉内的辐射传热是工业生产中常遇到的问题。过去，人们在应用热流法计算辐射传热时遇到了一定的困难，使计算结果与实际有一定的偏差。本文运用文献［１］中给出的新热流数学模型，开发出由新热流方程与能量方程相耦合的计算机程序，其中的比热流参数由线加热热源情况下计算得到。用该程序计算了实验室用马弗炉内的温度场，并且用热电偶实测了炉内的一些温度值，理论计算与实测值符合很好。     

三种新型流量计在醋酸装置中的应用

阐述了阿牛巴、超声波、电磁等3种流量计的性能特点、选用原则和安装要点。重点分析了低压甲醇羰基化生产醋酸装置中的各种介质的特点如强腐蚀性、两相流、低电导率等,根据不同介质的特点和工艺要求选用不同类型的流量计,并且总结了这些流量计替代原有孔板、涡街、涡轮流量计的实际使用情况以及经验教训。     

Sediment chemistry and nutrient influx in a hydrologically restored bottomland hardwood forest in Midwestern USA

Exchanges of total N and C between a river and its floodplain forest have been enhanced by sedimentation processes during flood pulses at a 5‐ha bottomland hardwood forest located at the Olentangy River Wetland Research Park in central Ohio. In the spring of 2000, the forest was hydrologically restored by notching an artificial levee that had separated the Olentangy River and its floodplain forest for 100 years. One‐hundred flat sediment traps (30 cm × 30 cm) were used to collect sediment samples during spring/summer flooding events from 2003 to 2005. Results showed that sediment deposition is determined by the landscape variability during flooding events, Net sediment deposit in the wettest area averaged 134 ± 12 g‐dry wt m^?2 in 2003, 127 ± 17 g‐dry wt m^?2 in 2004 and 149 ± 23 g‐dry wt m^?2 in 2005. Total N and C sedimentation ranged from 0.49 to 0.92 g‐N m^?2 and 5.2 to 19.9 g‐C m^?2. Fe dominates the sediment chemistry and results show the elemental abundance in the order of Al > Fe > Ca > K > Mg > S > P > Na > Mn > Zn > B > Cu > Mo. A hydrologic pulsing index (HPI) could be used as an indicator for mass changes of energies with hydrologic pulsing events. Restoration of seasonally flooded bottomland forests could stimulate potentially large nutrient and Fe releases, which would eventually lead to an enhanced forest productivity and biodiversity. Copyright © 2007 John Wiley & Sons, Ltd.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

油管漏磁探伤工艺与应用

简要介绍了漏磁探伤的基本原理及工艺流程与设备仪器，并对油管的常见损伤缺陷进行了分析。     

Heat transfer mechanism of a swirling impinging jet in a stagnation region

Heat transfer characteristics of a swirling impinging jet have been experimentally examined using a combined particle image velocimetry (PIV) and laser‐induced fluorescence (LIF) technique for simultaneous measurement of velocity and temperature fields. The present study shows that the radial width of the jet stretches with increasing swirl intensity, and that the stretching phenomenon contributes to the maximum local heat transfer coefficient. At the stagnation region, the flow near the heated surface is mixed intermittently by reverse flows toward upstream, and spatial distributions of temperature are correlated with instantaneous velocity vector maps. The dynamic behavior of recirculation zones, attributed to swirl number Sw and impinging distance, mainly determines the turbulent heat transfer at the stagnation region. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(8): 663–673, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10120     

Influence of numerical and viscous dissipation on shock wave reflections in supersonic steady flows

Numerical simulations are investigated to describe precisely the shock wave reflections in supersonic steady air flow field. The main objectives are to study the influence of the wedge trailing edge corner angle, of the numerical methods and of the viscous effects on the shock wave reflections and on the hysteresis behavior. The computations are done with different MUSCL-TVD finite volume schemes and the corresponding results are compared. The flow viscosity is also taken into account and comparisons are made between inviscid and viscous flow simulations. The results display the non-negligible influence of the numerical scheme accuracy on the results, mainly on the position and height of the Mach stem, and the relatively weak influence of the flow viscosity on these parameters. Comparisons between numerical results and experimental data have also been done and a good agreement is only observed for small wedge angles mainly due to the three-dimensional effects in the experimental setup.     

变压器有载合闸过程中故障分闸后铁心剩磁分析

通过有载合闸变压器模型,分析了变压器有载合闸过程中由于副边突然短路导致主保护动作时电流和磁通的暂态过程,并对变压器铁心内的剩磁作了定性的分析。