Investigation of corrosion properties with Ni–P/TiNO coating on aluminum alloy bipolar plates in proton exchange membrane fuel cell

Aluminum alloy bipolar plates have unique application potential in proton exchange membrane fuel cell (PEMFC) due to the characteristics of lightweight and low cost. However, extreme susceptibility to corrosion in PEMFC operation condition limits the application. To promote the corrosion resistance of aluminum alloy bipolar plates, a Ni–P/TiNO coating was prepared by electroless plating and closed field unbalanced magnetron sputter ion plating (CFUMSIP) technology on the 6061 Al substrate. The research results show that Ni–P interlayer improves the deposition effect of TiNO outer layer and increase the content of TiN and TiO_xN_y phases. Compared to Ni–P and TiNO single-layer coatings, the Ni–P/TiNO coating samples exhibited the lowest current density value of (1.10 ± 0.02) × 10^?6 A·cm^?2 in simulated PEMFC cathode environment. Additionally, potential cyclic polarization measurements were carried out aiming to evaluate the durability of the aluminum alloy bipolar plate during the PEMFC start-up/shut-up process. The results illustrate that the Ni–P/TiNO coating samples exhibit excellent stability and corrosion resistance.     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

Improved error performance for generalised spatial modulation with enhanced spectral efficiency

The existing analytical average bit error rate (ABER) expression of conventional generalised spatial modulation (CGSM) does not agree well with the Monte Carlo simulation results in the low signal‐to‐noise ratio (SNR) region. Hence, the first contribution of this paper is to derive a new and easy way to evaluate analytical ABER expression that improves the validation of the simulation results at low SNRs. Secondly, a novel system termed CGSM with enhanced spectral efficiency (CGSM‐ESE) is presented. This system is realised by applying a rotation angle to one of the two active transmit antennas. As a result, the overall spectral efficiency is increased by 1 bit/s/Hz when compared with the equivalent CGSM system. In order to validate the simulation results of CGSM‐ESE, the third contribution is to derive an analytical ABER expression. Finally, to improve the ABER performance of CGSM‐ESE, three link adaptation algorithms are developed. By assuming full knowledge of the channel at the receiver, the proposed algorithms select a subset of channel gain vector (CGV) pairs based on the Euclidean distance between all CGV pairs, CGV splitting, CGV amplitudes, or a combination of these.     

Modelling of chromatic contrast for retrieval of wallpaper images

Colour remains one of the key factors in presenting an object and, consequently, has been widely applied in retrieval of images based on their visual contents. However, a colour appearance changes with the change of viewing surroundings, the phenomenon that has not been paid attention yet while performing colour‐based image retrieval. To comprehend this effect, in this article, a chromatic contrast model, CAMcc, is developed for the application of retrieval of colour intensive images, cementing the gap that most of existing colour models lack to fill by taking simultaneous colour contrast into account. Subsequently, the model is applied to the retrieval task on a collection of museum wallpapers of colour‐rich images. In comparison with current popular colour models including CIECAM02, HSI and RGB, with respect to both foreground and background colours, CAMcc appears to outperform the others with retrieved results being closer to query images. In addition, CAMcc focuses more on foreground colours, especially by maintaining the balance between both foreground and background colours, while the rest of existing models take on dominant colours that are perceived the most, usually background tones. Significantly, the contribution of the investigation lies in not only the improvement of the accuracy of colour‐based image retrieval but also the development of colour contrast model that warrants an important place in colour and computer vision theory, leading to deciphering the insight of this age‐old topic of chromatic contrast in colour science. © 2014 Wiley Periodicals, Inc. Col Res Appl, 40, 361–373, 2015     

Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

Sensitivity analysis of Johnson-Cook material parameters on adiabatic shear in different directions

ABSTRACT

This study investigates the effects of strain, strain rates, and forming directions (RD-rolling direction, TD-transverse direction, and ND-normal direction) on adiabatic shear, via dynamic impact compression tests using the Split Hopkinson Pressure Bar (SHPB) apparatus. A modified Johnson-Cook (J-C) constitutive model is proposed, which used to analyse the influence of the constitutive parameters on the sensitivity of adiabatic shear, employing a finite element software. The different sensitivities of adiabatic shear under different directions are explained by combining microscopic analysis and results from mechanical responses. The results show that the sensitivity of adiabatic shear can be related to the time of stress collapse in the following trend: ND?>?TD?>?RD; the sensitivities of these constitutive parameters on adiabatic shear are calculated and compared.     

Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.