邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

Bandpass filters using periodically loaded combline resonators

A novel combline filter is proposed for cellular‐radio base stations. The Q‐factor is significantly improved. The eigenvalue equation is expressed with the single‐team approximation in the gap region of the combline resonator. A two‐pole combline filter is designed. The calculation, simulation, and experiment results are presented and are in good agreement. © 2005 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Reconstruction of Mandibular Defect with Porous β-TCP/BMG Artificial Bone

1Introduction Reconstructivesurgeryisoneofthehottestre searchedsubjectsthatdealingwithbonedefects.Thetra ditionalmethodisimplantationoffreshautograftbonebe causeofitsnon immunoreactiveproperty.Butautologousbonewasnotabundantinsomecases.Sowefoundbeta trica…     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Preparation and Compressive Stress Effect of Polymer Matrix RE-Fe Giant Magnetostrictive Composite

Polymer matrix RE-Fe giant magnetostrictire composite （GMPC） was prepared using bonding and magnetic field forming technique, and magnetostriction of samples was measured for different compressive stress. The experimental results show thai there is certain compressive effect in GMPC. And the influence of compressive stress on magnetostriction of sample was investigated. It offers essential reference for application and device design of GMPC.     

A stochastic realization algorithm via block LQ decomposition in Hilbert space

A stochastic realization problem of a stationary stochastic process is re-visited, and a new stochastically balanced realization algorithm is derived in a Hilbert space generated by second-order stationary processes. The present algorithm computes a stochastically balanced realization by means of the singular value decomposition of a weighted block Hankel matrix derived by a “block LQ decomposition”. Extension to a stochastic subspace identification method explains how the proposed abstract algorithm is implemented in system identification.     

Average consensus in networks of dynamic agents with switching topologies and multiple time-varying delays

In this paper, we discuss average consensus problem in undirected networks of dynamic agents with fixed and switching topologies as well as multiple time-varying communication delays. By employing a linear matrix inequality method, we prove that all the nodes in the network achieve average consensus asymptotically for appropriate communication delays if the network topology is connected. Particularly, several feasible linear matrix inequalities are established to determine the maximal allowable upper bound of time-varying communication delays. Numerical examples are given to demonstrate the effectiveness and the sharpness of the theoretical results.