Optical scattering in beef steak to predict tenderness using hyperspectral imaging in the VIS-NIR region

The objective of this research is to develop a non-destructive method for predicting cooked beef tenderness using optical scattering of light on fresh beef muscle tissue. A hyperspectral imaging system (λ = 496–1,036 nm) that consists of a CCD camera and an imaging spectrograph, was used to acquire beef steak images. The hyperspectral image consisted of 120 bands with spectral intervals of 4.54 nm. Sixty-one fresh beef steaks, including 44 strip loin and 17 tenderloin cuts, were collected. After imaging, the steaks were cooked and Warner-Bratzler shear (WBS) force values were collected as tenderness references. The optical scattering profiles were derived from the hyperspectral images and fitted to the modified Lorentzian function. Parameters, such as the peak height, full scattering width at half maximum (FWHM), and the slope around the FWHM were determined at each wavelength. Stepwise regression was used to identify 7 key wavelengths and parameters. The parameters were then used to predict the WBS scores. The model was able to predict WBS scores with an R = 0.67. Optical scattering implemented with hyperspectral imaging shows limited success for predicting current status of tenderness in beef steak.     

艺术建筑设计的探索

通过徐州一中艺术楼的设计实践，寻求优美而独特的艺术形象，并用纯几何形体的组合来达到功能与形式的完美统一。     

Prediction of the twisting moment and axial force in a circular rubber cylinder for combined extension and torsion based on the logarithmic strain approach

The scope of the present work is the application of a particular class of strain energy function, based on the logarithmic strain, for the prediction of the twisting moment and axial force of a rubber circular cylinder under combined extension and torsion. The strain energy function involves four material parameters three of which are determined by fitting published experimental data from simple tensile and compression tests of natural rubber. One of the parameters of the proposed model has physical meaning, and it is equal to one ninth of the initial modulus of elasticity of the material. Hence, the number of unknown parameters is reduced to three. The logarithmic strain energy function is then applied to a combined extension and torsion problem of a rubber circular cylinder to check its performance for more complicated deformations. The results are compared with corresponding experimental and theoretical solutions available in the literature to validate the proposed model. It is found that the proposed strain energy function apart from predicting the common modes of deformations is also capable to determine more complicated types of deformation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Dynamic analysis of the NPP pressure sensor system

The aim of the work was to develop on-line methods of control and diagnostics of pressure sensors at a NPP. The analysis was carried out along two lines:

1. i) The detection system including the sensor itself was modeled theoretically to obtain and study its transfer function, and to establish correspondence between the spectral characteristics of the pressure signal.

2. ii) The numerical processing of the signal using the AR technique to reconstruct the transfer function and evaluate the system's response, to a step impulse, as well as the spectral analysis. The hydraulic model presented indicate that the spectral lines observed at 10 Hz are due to longitu-dinal oscillations of water in the system branches, while the response time of the detection system is effectively the time of signal retardation in the porous ceramic diaphragms of the δ-cell of the sensor itself.

     

智能化红外焊缝检测仪的实时信号自相关分析

详细介绍了在改进红外焊缝检测仪的过程中实时信号的一种抗干扰方法－－自相关方法。重点离自相关方法的数学模型，软件框图及设计思想，并给出了实验结果。     

Stability analysis and antiwindup design of uncertain discrete-time switched linear systems subject to actuator saturation

This paper investigates the stability analysis and antiwindup design problem for a class of discrete-time switched linear systems with time-varying norm-bounded uncertainties and saturating actuators by using the switched Lyapunov function approach.Supposing that a set of linear dynamic output controllers have been designed to stabilize the switched system without considering its input saturation,we design antiwindup compensation gains in order to enlarge the domain of attraction of the closed-loop system in the presence of saturation.Then,in terms of a sector condition,the antiwindup compensation gains which aim to maximize the estimation of domain of attraction of the closed-loop system are presented by solving a convex optimization problem with linear matrix inequality(LMI)constraints.A numerical example is given to demonstrate the effectiveness of the proposed design method.     

Structural analysis of Au/Mg(OH)2 during deactivation by Debye function analysis

Using a Debye function analysis, the presence of icosahedral and face centered cuboctahedral gold in a 1 1 ratio has been found in freshly prepared Au/Mg(OH)₂ catalyst. The results support earlier studies which suggest the icosahedral form to be more stable at small nanometer sizes. Interactions between the gold and the Mg(OH)₂ support appear to be weak, with the gold rapidly coagulating over a period of three months. Re-analysis of the aged sample shows the gold to be mainly in the form of truncated decahedra.     

进口刀盘圆环失效原因及改进

首先从材料力学角度分析了抚顺石化公司干法腈纶装置原进口切断刀盘圆环失效的原因 ,认为此种切断刀盘圆环系二维增强结构层压板 ,层间没有纤维增强 ,需要解决由二维增强向三维增强的过渡。给出了改进办法 ,寻求到三维增强的替代材料。同时介绍了机械加工测试及在线实验     

光学镜头调制传递函数的测试

为了定量、客观、全面地评价光学镜头的像质,介绍了光学镜头调制传递函数的测试。先简要叙述了测试的原理,并给出计算公式;然后介绍了测试步骤,其中包括固定、穿轴、测试中心视场和测试轴外视场;最后介绍了测试时的注意事项,包括对测试工装的要求、对测试平面的要求和正、负轴外视场测试值相差较大时的处理办法。