用ADT14设计的新型电子温控器

ADT14是一种可编程温度监控器电路，可广泛应用于各种控制系统中进行温度检测和控制。用ADT14设计的新型电子温控器具有结构简单，安装方便，温控准确等优点。     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

转制科研单位建立和完善内部会计控制的探讨

针对目前大多数科研单位在内部会计控制中存在的问题,根据财政部颁布的《内部会计控制规范一基本规范》,探讨了科研单位在转制过程中应如何建立和完善内部会计控制制度,以达到防范经营风险,保护资产安全、完整,确保经营管理目标和政策有效实施.     

Mechanical properties of poly(ether-ether-ketone) for engineering applications

An outline of the characteristics of PEEK and the versatility of its compositional forms (micro and macro composites) are given to illustrate its wide potential for success in engineering applications. Although it is necessary to have particular tabulations of mechanical properties for engineering design, these are seldom available and consequently it is argued that an understanding of stiffness, toughness and strength properties are required to fully exploit available manufacturer's data and thus develop the full potential of PEEK and its composites. Stiffness characteristics are considered in terms of a modulus function which is dependent on time under load and temperature. In its composite forms, whether reinforced with short or continuous fibres, stiffness anistropy can be both considerable and complex, but some empirical ground-rules are apparent. For continuous fibre composites even in the form of complex lay-ups, it is also possible to attempt some stiffness prediction from certain pseudo-elastic constants. Toughness of PEEK and its composites is described in terms of both comparative and intrinsic properties. Instrumented falling weight impact data, particularly as a function of temperature enable some insight into ductile-brittle transitions for the unreinforced material, but crack initiation and crack propagation processes for the various fibre reinforced forms. Intrinsic toughness is described in terms of linear elastic fracture mechanics theory. Strength properties are described for static and dynamic loading configurations. In particular, PEEK and its composites are evaluated for increasing test severities for strength characteristics; stress concentration, loading form and test temperature are considered.     

Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002     

A hybrid PC/PLC architecture for manufacturing-system control—theory and implementation

This paper presents a novel and generic PC/PLC-based software/hardware architecture for the control of flexible manufacturing workcells. The proposed implementation methodology is based on the utilization of any one of the available formal discrete-event-system control theories in conjunction with state-of-the-art industrial programmable-logic controllers (PLCs). The methodology has been illustrated to be a viable technique through its actual implementation in our laboratory using a robotic-workcell testbed. The specific control theory used is a combination of Extended Moore Automata and Ramadge-Wonham Automata that has been developed by our research group. The modular control software architecture has been developed for MS-Windows environments (running on one PC interfaced to the PLCs) and allows the use of different formal control theories as well as different commercial PLC hardware. The effective graphical user interface provides a transparent programming environment, where users are not expected to have a full knowledge of the formal control theory used.     

卫星遥感测控的系统融合技术

卫星遥感测控系统包括运载火箭飞行测控，卫星运行测控，有效载荷设备测控以及它本身应完成的遥感测量，高效完备的系统融合技术采用包括视频综合技术，统一载波宽带传输技术，地面站多功能统一测控技术，软件化技术，载波综合利用技术等，大大简化了卫星遥感的测控设备。     

Application of Fuzzy Control into a New Kind of Sea Water Still

ＡｐｐｌｉｃａｔｉｏｎｏｆＦｕｚｚｙＣｏｎｔｒｏｌｉｎｔｏａＮｅｗＫｉｎｄｏｆＳｅａＷａｔｅｒＳｔｉｌＱｕＷｅｉｄｏｎｇＹｕＪｉｎｄｉＺｈａｎｇＨｅｆｅｉＮｏｒｔｈｗｅｓｔｅｒｎＰｏｌｙｔｅｃｈｎｉｃａｌＵｎｉｖｅｒｓｉｔｙＸｉ′ａｎ７１００７２，Ｐ...