The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

Effect of 3D lip deformations on elastohydrodynamic lip seals behaviour

The numerical simulation of comparative elastohydrodynamic lubrication between axisymmetrical and 3D elastic approaches on the radial lip seals is presented in order to determine the 3D effect of the elastic aspect of the seal lip. Indeed, the consideration of 3D model in other words the circumferential variation of the lip elastic deformation indicated a difference in the deformation distribution of the lip compared to the axisymmetrical approach. Consequently, the results show that the presence of the circumferential variation of the seal lip deformation has a significant effect on the pumping rate values.     

增强大学生职业规划效果的宏观对策

针对目前大学生职业规划效果不佳的现状，分析了导致大学生职业规划效果不佳的原因，提出了增强大学生职业规划效果的宏观对策。     

Optically tuned superconductive-dielectric resonators with whispering-gallery modes

An analytical method is presented for calculating the resonant frequency andQ-factor of a superconducting dielectric disk resonator operating in millimeter-wave regime with whispering-gallery mode. Resonant frequency shift due to the optical generation of quasi-particles in superconducting film is investigated as a function of photon flux. An optically tunable resonant frequency of about 500 MHz is estimated, and good agreement is found between numerical results and experimental ones.     

Drying of Prone to Twist Boards in a Pre-Twisted Position

A method to minimize twist has been investigated; i.e., drying the boards in a pre-twisted position. It has been found that Norway spruce boards can be deformed toward straightness by this method. The force exerted by a board on its holders during drying in a pre-twisted position has been measured. When the variation in torsional stiffness as a function of temperature and moisture content is accounted for, it is found that a creep deformation of the board occurs both during the drying phase and the cooling phase. In addition to mechano-sorptive creep, a deformation released by a change in temperature also seems to occur.     

高梯度加速管的束流传输

对不同能量、不同质量数、不同初始条件的入射束和有无空间电荷效应的离子束流在高梯度加速管中的传输进行了计算，并讨论了一些影响加速管聚焦作用的主要因素，计算结果与实际情况相符。     

X-射线荧光增量法测定硅铁合金中的Ca、Ba

介绍了X-射线荧光增量法同时测定硅铁合金中的Ca、Ba，探讨了基体效应校正、扩展曲线的应用范围，方法准确度和精度高。     

"十五"期间涟钢发展循环经济项目的主要内容及效果

介绍了涟钢在"十五"期间实施的循环经济项目:如燃气-蒸汽联合循环发电、小高炉TRT、焦化干熄焦、矿渣粉生产线、免烧承重砖等以及实施的效果.     

Effect of Microstructure on the Accelerated Creep of 20CrMoV12‐1 and P 91 Steels

In the initial part the change of microstructure for steel X20 CrMoV 121 is discussed in terms of the distribution of carbide precipitates and its effects on accelerated creep resistance and hardness are presented. In the following, experimental results of microstructure and accelerated creep resistance are presented for the steels X20CrMoV 121 and P91 annealed for up to 8760 hours at 650°C and 750°C before the testing. A similar evolution of the distribution of carbide particles of a size above 102 nm is found for both steels, while the accelerated creep resistance is diminished much stronger for the steel X20CrMoV 121. This difference is due to a greater stability of NbC than that of VC precipitates, both related to the evolution of the chemical composition of complex chromium, molybdenum and iron carbide particles.     

AlSn20Cu/Steel双金属板(带)复合轧制过程的厚度匹配

通过对AlSn20Cu/Steel双金属板(带)复合轧制过程变形区变形规律的分析，确定了轧制过程的总变形率与各分层变形率的关系，解决了实际生产中各分层原料的厚度匹配问题。