Carbon supported bimetallic Ru‐Co catalysts for H2 production through NaBH4 and NH3BH3 hydrolysis

This work investigates the effect of the addition of small amounts of Ru (0.5‐1 wt%) to carbon supported Co (10 wt%) catalysts towards both NaBH₄ and NH₃BH₃ hydrolysis for H₂ production. In the sodium borohydride hydrolysis, the activity of Ru‐Co/carbon catalysts was sensibly higher than the sum of the activities of corresponding monometallic samples, whereas for the ammonia borane hydrolysis, the positive effect of Ru‐Co systems with regard to catalytic activity was less evident. The performances of Ru‐Co bimetallic catalysts correlated with the occurrence of an interaction between Ru and Co species resulting in the formation of smaller ruthenium and cobalt oxide particles with a more homogeneous dispersion on the carbon support. It was proposed that Ru^°, formed during the reduction step of the Ru‐Co catalysts, favors the H₂ activation, thus enhancing the reduction degree of the cobalt precursor and the number of Co nucleation centers. A subsequent reduction of cobalt and ruthenium species also occurs in the hydride reaction medium, and therefore the state of the catalyst before the catalytic experiment determines the state of the active phase formed in situ. The different relative reactivity of the Ru and Co active species towards the two investigated reactions accounted for the different behavior towards NaBH₄ and NH₃BH₃ hydrolysis.     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Modelling of black carbon statistical distribution and return periods of extreme concentrations

Eight datasets of 1-h black carbon (BC) concentrations measured in Warsaw agglomeration (Poland), at urban background and sub-urban sites, and in Racibórz, a small town in Upper Silesia district (regional background site) were analyzed to evaluate BC levels, daily profiles and statistical distributions of concentrations in Central-Eastern European region. The observed mean levels ranged from 1483 ng m⁻³ in suburban site during summer to 3358 ng m⁻³ in regional background site in winter. Observed diurnal patterns were bimodal in the locations dominated by traffic emissions, but unimodal, with elevated evening peak in individually heated residential area. Three theoretical frequency distributions were applied to fit analyzed datasets separately. The lognormal distribution was the most appropriate to represent the middle-range values, while the high concentrations were satisfactorily predicted by the type I two-parameter exponential distribution which was used to estimate the return periods of extreme concentrations for winter months.     

开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

An efficient manufacturing method for I-shaped cross-sectional CFRP beam with arbitrary arrangement of carbon fiber using electro-activated resin molding

Abstract

The I-shaped cross-sectional beam of CFRP (CFRP I-beam) is usually manufactured by the continuous protrusion method. Carbon fibers can only be arranged in the longitudinal direction. The CFRP I-beam with arbitrary arrangement of carbon fiber was manufactured with applying the electro-activated deposition molding method. The carbon fiber fabric was immersed in the deposition solution and energized, epoxy resin precipitated around carbon fiber and impregnated. The resin-impregnated fabric was installed to the mold, and the CFRP I-beam was fabricated. The CFRP I-beam was subjected to three-point bending tests, and the relationship between load-deflection was simulated by finite-element analysis.     

Solar light-driven reduction of crystal violet by a composite of g-C3N4, β-Ag2Se, γ-Fe2O3 and graphite

Abstract

In this work, a new g-C₃N₄-based Z-scheme with γ-Fe₂O₃ and β-Ag₂Se both n-type semiconductors, and graphite to favor electron exchange is presented. The composite material was studied by XRD, FTIR, UV-Vis, TEM, XPS, TGA, DSC and TOF-SIMS, and the ability of this photocatalytic system to act as a photo-reductant was assessed using crystal violet (CV⁺) dye. Solar light driven photo-reduction of CV⁺ in the presence of tri-sodium citrate evidenced a synergistic enhancement of the activity of the composite toward reduction, with ～20 times higher conversion rates per unit of surface area than those of g-C₃N₄. Photo-oxidation experiments under Xe lamp irradiation in the presence of H₂O₂ also showed that the AgFeCN composite featured a higher activity (～8×) than g-C₃N₄. This Z-scheme may deserve further study as a photo-reductant to obtain hydrogen or hydrogenated compounds. Moreover, the use of CV⁺ may represent a facile procedure that can aid in the selection of new photocatalysts to be used in hydrogen production.