全文获取类型
收费全文 | 75篇 |
免费 | 15篇 |
国内免费 | 10篇 |
专业分类
综合类 | 7篇 |
化学工业 | 11篇 |
金属工艺 | 16篇 |
机械仪表 | 7篇 |
建筑科学 | 15篇 |
矿业工程 | 7篇 |
轻工业 | 1篇 |
水利工程 | 4篇 |
石油天然气 | 2篇 |
武器工业 | 2篇 |
无线电 | 2篇 |
一般工业技术 | 16篇 |
冶金工业 | 10篇 |
出版年
2023年 | 2篇 |
2022年 | 5篇 |
2021年 | 3篇 |
2020年 | 2篇 |
2019年 | 2篇 |
2018年 | 3篇 |
2017年 | 6篇 |
2016年 | 5篇 |
2015年 | 6篇 |
2014年 | 5篇 |
2013年 | 4篇 |
2012年 | 4篇 |
2011年 | 6篇 |
2010年 | 6篇 |
2009年 | 2篇 |
2008年 | 5篇 |
2007年 | 7篇 |
2006年 | 8篇 |
2005年 | 5篇 |
2004年 | 4篇 |
2002年 | 1篇 |
2001年 | 1篇 |
2000年 | 1篇 |
1999年 | 2篇 |
1998年 | 1篇 |
1995年 | 1篇 |
1993年 | 1篇 |
1982年 | 1篇 |
1979年 | 1篇 |
排序方式: 共有100条查询结果,搜索用时 15 毫秒
21.
通过研究三钢1号小方坯连铸机振动参数,对比各种工艺对铸坯表面质量的影响,改善了铸坯的表面质量。振动参数优化如下:结晶器振动方式由采用正弦振动改为非正弦振动,偏斜率[ɑ]采用0.2,振动频率由152次/min提高至182 次/min,振动幅度由8.2 mm降低至7.2 mm,负滑脱时间由0.168 s降低至0.117s,铸坯表面质量得到有效改善。同时在保证铸坯表面质量的情况下,可以通过适当的提高连铸拉速,减少铸坯振痕深度。 相似文献
22.
23.
通过万能拉伸试验机、金相显微镜、扫描电镜并结合能谱分析仪和透射电镜对Nb-V不同微合金化的高强钢筋在单轴拉伸过程中的断裂行为进行了表征。结果表示,实验钢心部组织为铁素体+珠光体+贝氏体,随着实验钢筋中Nb含量的降低,贝氏体组织体积分数下降(50%~3%)。拉伸断口呈韧性断裂,断口以韧窝为主,随着贝氏体组织体积分数的降低,韧窝尺寸和深度先增大后减小。裂纹和断口处的夹杂主要为MnS和氧化物。微裂纹多形成于相界面或夹杂处,也有形成在铁素体基体内,裂纹尺寸随着贝氏体组织体积分数的降低而增大。当裂纹在扩展过程中遇到较硬相贝氏体时,会向较软的铁素体相扩展。 相似文献
24.
25.
介绍了水泥混凝土路面施工中的常见病害,并分析了病害产生原因,论述了病害的相应预防措施,阐明了施工管理的主要作用,从根本上防止和消除病害的产生。 相似文献
26.
为了从微观结构角度对水泥稳定碎石微裂自愈合性能进行量化和直观的分析,利用数显式裂缝宽度监测仪KON-FK(B)和万向体视显微镜XTZ-05T对不同微裂程度下微裂缝随龄期增长变化的宽度值和微裂缝内部自愈产物随龄期的生成情况进行实时监测和观察分析.并通过SPSS软件的描述性统计功能对所测微裂缝宽度值进行统计分析,得出不同微裂程度及愈合后微裂缝的宽度值分布范围;基于像素面积计算法原理,借助图像处理软件Imagemagick对微裂缝随龄期增长自愈合情况的图像进一步处理分析并计算,得出不同龄期下愈合产物的覆盖率及不同微裂程度下愈合覆盖率的对数拟合方程.结果表明:微裂后的水泥稳定碎石裂缝宽度值随龄期逐渐减小,且微裂缝内部生成的愈合产物覆盖率不断增长,后期基本可达完全愈合状态.从而证明了微裂后的水泥稳定碎石在宏观力学性能和微观结构特性上均具有良好的自愈合效果. 相似文献
27.
A differential excitation probe based on eddy current testing technology was designed. Sheet specimens of Q235 steel with prefabricated micro-cracks of different widths and of aluminum with prefabricated micro-cracks of different depths were detected through the designed detection system. The characteristics of micro-cracks can be clearly showed after signals processing through the short-time Fourier transform (STFT). By changing the parameter and its value in detecting process, the factors including the excitation frequency and amplitude, the lift-off effect and the scanning direction were discussed, respectively. The results showed that the differential excitation probe was insensitive to dimension and surface state of the tested specimen, while it had a high degree of recognition for micro-crack detection. Therefore, when the differential excitation detection technology was used for inspecting micro-crack of turbine blade in aero-engine, and smoothed pseudo Wigner-Ville distribution was used for signal processing, micro-cracks of 0.3.mm depth and 0.1.mm width could be identified. The experimental results might be useful for further research on engineering test of turbine blades of aero-engine. 相似文献
28.
29.
针对目前漏磁检测抽油杆微裂纹的精度和灵敏度不高的现状,提出一种通过拉伸抽油杆使微裂纹张开后的漏磁检测法。该方法在材料弹性范围内,使用液压装置拉伸微裂纹,在4MPa拉伸应力下对带有0.1、0.3mm人工裂纹45钢的试验样杆的检测结果表明,0.1mm微裂纹输出增加值为0.243mm;0.3mm裂纹输出增加值为0.097mm,不仅能够保证抽油杆的无损检测,而且与常规方法相比,在相同条件下,可提高微裂纹的检测精度和灵敏度。这为提高现场抽油杆漏磁检测微裂纹的精度和灵敏度提供了一个有效的途径。 相似文献
30.