Structural analysis and optimization of a tethered swept wing for airborne wind energy generation

In this paper, we present an aero‐structural model of a tethered swept wing for airborne wind energy generation. The carbon composite wing has neither fuselage nor actuated aerodynamic control surfaces and is controlled entirely from the ground using three separate tethers. The computational model is efficient enough to be used for weight optimisation at the initial design stage. The main load‐bearing wing component is a nontypical “D”‐shaped wing‐box, which is represented as a slender carbon composite shell and further idealised as a stack of two‐dimensional cross section models arranged along an anisotropic one‐dimensional beam model. This reduced 2+1D finite element model is then combined with a nonlinear vortex step method that determines the aerodynamic load. A bridle model is utilised to calculate the individual forces as a function of the aerodynamic load in the bridle lines that connect the main tether to the wing. The entire computational model is used to explore the influence of the bride on the D‐box structure. Considering a reference D‐box design along with a reference aerodynamic load case, the structural response is analysed for typical bridle configurations. Subsequently, an optimisation of the internal geometry and laminate fibre orientations is carried out using the structural computation models, for a fixed aerodynamic and bridle configuration. Aiming at a minimal weight of the wing structure, we find that for the typical load case of the system, an overall weight savings of approximately 20% can be achieved compared with the initial reference design.     

增材制造技术在超高膨胀封隔器中的应用

石油和天然气行业不断关注增材制造技术在航空航天和汽车行业的应用发展。研发了利用增材制造技术的超高膨胀封隔器,该封隔器的支承环系统由增材制造。增材制造设计大幅减少了支承系统的构件数量,同时显著提高了膨胀能力和额定压力。密封元件系统与增材制造支承环安装在一起,提供了极端膨胀比、零挤压间隙和对不规则孔的良好适应性。分析和测试结果表明:直径膨胀比高达111%,与常规封隔器相比,提高50%以上; 至少涵盖5种线重的套管(外径相同); 在148.89 ℃的温度下,密封元件能够保持压力68.95 MPa。介绍了增材制造技术、增材制造支承环概念、增材制造材料力学性能、密封元件系统优化和测试情况,以期给我国的完井作业提供借鉴。     

Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

Psychrophilic hydrogen production from petrochemical wastewater via anaerobic sequencing batch reactor: techno-economic assessment and kinetic modelling

Independent hydrogen production from petrochemical wastewater containing mono-ethylene glycol (MEG) via anaerobic sequencing batch reactor (ASBR) was extensively assessed under psychrophilic conditions (15–25 °C). A lab-scale ASBR was operated at pH of 5.50, and different organic loading rates (OLR) of 1.00, 1.67, 2.67, and 4.00 gCOD/L/d. The hydrogen yield (HY) progressed from 134.32 ± 10.79 to 189.09 ± 22.35 mL/gMEG_initial at increasing OLR from 1.00 to 4.00 gCOD/L/d. The maximum hydrogen content of 47.44 ± 3.60% was achieved at OLR of 4.0 gCOD/L/d, while methane content remained low (17.76 ± 1.27% at OLR of 1.0 gCOD/L/d). Kinetic studies using four different mathematical models were conducted to describe the ASBR performance. Furthermore, two batch-mode experiments were performed to optimize the nitrogen supplementation as a nutrient (C/N ratio), and assess the impact of salinity (as gNaCl/L) on hydrogen production. HY substantially dropped from 62.77 ± 4.09 to 6.02 ± 0.39 mL/gMEG_initial when C/N ratio was increased from 28.5 to 114.0. Besides, the results revealed that salinity up to 10.0 gNaCl/L has a relatively low inhibitory impact on hydrogen production. Eventually, the cost/benefit analysis showed that environmental and energy recovery revenues from ASBR were optimized at OLR of 4.0 gCOD/L/d (payback period of 7.13 yrs).     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

A review of the existing performance verification infrastructure for micro-CMMs

The performance verification of micro-CMMs is now of intense interest because of their capability to perform length measurements in three dimensions to high accuracy with low uncertainties. Currently, verification of micro-CMMs is completed in the spirit of existing specification standards, because strict adherence to these standards is often difficult. This review aims to present and discuss verification techniques available for micro-CMMs: specification standards, existing calibrated test lengths and traceability routes that can be associated with micro-CMMs. Three specification standards used in the testing of CMMs will be considered. In addition, a wide range of calibrated test lengths are reported, and any advantages and disadvantages associated with their use are discussed. It is concluded that micro-CMMs cannot yet be verified in accordance with existing specification standards. Suggestions are made for future standardisation work required to rectify these issues.     

Stochastic free vibration analyses of composite shallow doubly curved shells – A Kriging model approach

This paper presents the Kriging model approach for stochastic free vibration analysis of composite shallow doubly curved shells. The finite element formulation is carried out considering rotary inertia and transverse shear deformation based on Mindlin’s theory. The stochastic natural frequencies are expressed in terms of Kriging surrogate models. The influence of random variation of different input parameters on the output natural frequencies is addressed. The sampling size and computational cost is reduced by employing the present method compared to direct Monte Carlo simulation. The convergence studies and error analysis are carried out to ensure the accuracy of present approach. The stochastic mode shapes and frequency response function are also depicted for a typical laminate configuration. Statistical analysis is presented to illustrate the results using Kriging model and its performance.     

A GIS plug-in for Bayesian belief networks: Towards a transparent software framework to assess and visualise uncertainties in ecosystem service mapping

The complexity and spatial heterogeneity of ecosystem processes driving ecosystem service delivery require spatially explicit models that take into account the different parameters affecting those processes. Current attempts to model ecosystem service delivery on a broad, regional scale often depend on indicator-based approaches that are generally not able to fully capture the complexity of ecosystem processes. Moreover, they do not allow quantification of uncertainty on their predictions. In this paper, we discuss a QGIS plug-in which promotes the use of Bayesian belief networks for regional modelling and mapping of ecosystem service delivery and associated uncertainties. Different types of specific Bayesian belief network output maps, delivered by the plug-in, are discussed and their decision support capacities are evaluated. This plug-in, used in combination with firmly developed Bayesian belief networks, has the potential to add value to current spatial ecosystem service accounting methods. The plug-in can also be used in other research domains dealing with spatial data and uncertainty.     

无线电综合测试仪校准装置的研究及其不确定度分析

This calibration device of radio comprehensive tester is studied and established in this paper. It solves the verification and calibration of a large number of general-purpose radio comprehensive testers. The calibration device consists of four calibration sub- systems and calibration software system, including RF generator, audio generator, audio analyzer and RF analyzer. It also researches on the configuration of standard equipment and analyzes the uncertainty of the calibration devices, ensuring accurate and reliable val- ue transfer.     

浅谈枪支(弹药)库室电子技防测试

一个完整枪支(弹药)库室的安全防范由管理要求、物防要求、技防要求及人防要求完美的结合而成,其中技防要求是需要根据枪支(弹药)库室现场实体情况采取的一项电子技术手段,是起到安全预报警的最佳方式。本文就枪支(弹药)库室安全防范在技防要求方面按现行GA 1016-2012标准在检测中存在的问题做一些探讨、建议,以期为需要枪支(弹药)库室的建设单位、施工单位提供参考。