吸湿介质对碳纤维增强铸型尼龙复合材料的吸湿行为及力学性能的影响

本文对碳纤维增强铸型尼龙(CF／MC 尼龙)复合材料在不同吸湿介质中的吸湿行为进行了研究。结果表明，对于纤维体积分数为10％的碳纤维增强铸型尼龙复合材料(10％CF／MC尼龙复合材料)，随着吸湿介质的PH值减小，它的吸湿率增大。同时，经过吸湿后，10％CF／MC尼龙复合材料的弯曲强度有明显的下降。随着吸湿介质的PH值减小，试样的弯曲强度下降。使用环境扫描电子显微镜观察在10％HCl溶液中吸湿的试样的剪切断口形貌，得到的结果与吸湿实验的结果一致。     

重碱加压过滤的研究探索

在化工领域偿试使用加压过滤技术处理重碱，使重碱水份由真空过滤的１８～２０％降为加压过滤的１２％，可使生产厂家降低能耗；节约返碱     

可双固化树枝形聚酰胺-胺树脂的合成及其涂膜性能研究

探讨了以乙二胺与丙烯酸甲酯交替反应，制备了1．5，2．5代树枝形聚酰胺一胺树脂（PAMAM），对其用甲基丙烯酸缩水甘油酯（GMA）和γ-氨丙基三乙氧基硅烷进行了改性，使其能够紫外光固化和潮气固化。热分析考查了玻璃化温度和热稳定性，并进行了硬度、光泽、光固化速度、潮气固化速度、附着力、柔韧性等测试。     

高含水率杨木单板室温胶合的脲醛树脂胶研究

在实验室条件下 ,以传统脲醛树脂胶的生产工艺为基础 ,加用氨基取代羧酸类化合物。新配方制得脲醛树脂胶 ,用DSC分析了树脂固化反应热过程 ,对含水率在 12 % -2 0 %杨木单板进行了室温胶合研究     

聚丙烯接枝马来酸酐增容聚酰胺6／聚丙烯体系吸湿性能及力学性能的研究

以聚丙烯接枝马来酸酐(PP-g-MAH)为相容剂，利用其与聚酰胺6(PA6)在共混过程中的反应增容作用，实现了与聚丙烯(PP)之间的相容性共混，改变其用量，制备了系列具有不同组成的PA6／PP合金，研究了不同组成合金材料的吸湿性能及其在干态和充分吸湿状态时的冲击强度和拉伸性能。结果表明，向PA6／PP合金体系中加入相容剂PP-g-MAH后，可以改善合金的相界面，形成相容性的合金结构，明显降低合金材料的吸湿量及吸湿速率，但进一步增大相容剂PP-g-MAH的用量时，只能明显降低合金材料吸湿过程初期的吸湿速率，不能进一步显著降低合金材料的吸湿量。在相容剂PP-g-MAH用量一定时，随着PA6／PP合金体系中PA6组分含量的提高，合金在干、湿态条件下的冲击强度、拉伸强度、断裂伸长率均呈近似线性变化。对于具有相同基本组成的合金，随着相容剂PP-g-MAFI用量的增加，材料在干、湿态条件下的拉伸强度均有提高，杨氏模量则在干态时有所提高，在湿态时影响不显著，在干、湿态时断裂伸长率以及冲击强度均没有产生显著影响。     

Synthesis and physicochemical study of bisphenol‐C‐formaldehyde‐toluene diisocyanate polyurethane–jute and jute–rice husk/wheat husk composites

Bisphenol‐C‐formaldehyde‐toluene‐2,4‐di isocyanate polyurethane (PU) has been synthesized at room temperature and used for the fabrication of jute and jute–rice husk/wheat husk hybrid composites. PU–jute and PU–jute–RH/WH composites were prepared under pressure of 30.4 MPa at room temperature for 8 h, while PU–jute–RH/WH composites were prepared under same pressure at 110°C for 5 h. PU–jute composite has good tensile strength and flexural strength (50–53 MPa), while PU–jute–RH/WH hybrid composites have moderate tensile strength (9–11 MPa) and a fairly good flexural strength (15–31 MPa). Composites possess 1.1–2.2 kV electric strength and 0.94–1.26 × 10¹² ohm cm volume resistivity. Water absorption in PU–jute composite is different in water (9.75%), 10% HCl (12.14%), and 10% NaCl (6.05%). Equilibrium water uptake time in salt environment is observed 96 h, while in pure water and acidic environments it is 192 h. In boiling water equilibrium water content and equilibrium time are found to be 21.7% and 3 h, respectively. Water absorption increased 2.2 times in boiling water, whereas equilibrium time reduced 64 times. Thus, PU–jute composite has excellent hydrolytic stability against boiling water, 10% HCl, and 10% NaCl solutions. Fairly good mechanical and electrical properties and excellent hydrolytic stability of composites signify their usefulness for low cost housing units and in electrical and marine industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2363–2370, 2006     

The Effect of Moisture Content in Epoxy Film Adhesives on their Performance. III: Bulk Properties

Humidity absorbed by epoxy film adhesives during low temperature storage or exposure to atmosphere may result in reversible changes and irreversible modifications. Vacuum treatment may partially remedy the reversible changes. The consequences of vacuum drying are manifested in enhancement of both the peel and shear properties of bonded joints (Part I and Part II of this series of papers) and the thermal, physical and mechanical properties of the bulk adhesive, characterized in the present study.

Experimental results have shown that the bulk properties of structural epoxy based adhesives are highly correlated with the aging processes caused by water absorption in the prepolymerized adhesive. Applying the vacuum process is harmful to fresh unaged adhesive due to devolatization of low molecular species of the film adhesive.

The characterization of bulk properties for the purpose of following the aging and recovery processes is advantageous, since the bulk is independent of geometrical and interfacial effects which dominate in the case of property evaluation of the adhesive in a bonded joint.     

Viscoelastic properties of cellulose derivatives: 1. Cellulose acetate

The dynamic mechanical spectrum of cellulose acetate (CA) from −130°C to 240°C has been determined at different frequencies (from 0.1 to 30 Hz). Three relaxations, designated , β and γ in order of decreasing temperature, and one shoulder (β*) above room temperature were found. Comparison with calorimetric and thermogravimetric measurements yields the conclusion that the relaxation (197°C at 3 Hz) is related to the glass-to-rubber transition and the β* shoulder (50°C–100°C) is due to loss of moisture. The β relaxation (−38°C at 3 Hz, ΔH = 100 kJ mol⁻¹) is tentatively assigned to local motions of the main chain (glucopyranose rings). The low-temperature γ relaxation (−88°C at 3 Hz, ΔH = 46 kJ mol⁻¹), is humidity-dependent: its intensity decreases when the samples are dried to moisture contents lower than that obtained by normal room conditioning (about 3%). Higher water contents shift the relaxation to lower temperatures without increasing the intensity of the mechanical loss. It is suggested that water associated with the unesterified methylol groups of cellulose acetate is responsible of the dynamic mechanical γ dispersion.     

日本钢管福山焦化厂简介

介绍了福山焦化厂备煤、炼焦和化产回收系统的工艺及设备情况,并对煤调湿及干熄焦部分作了详述。     

碳化钙气压法快速测定砌块含水率

开发新型工程现场快速检测砌块含水率方法,与传统的烘箱干燥方法进行比较,开展了工程现场试验,研究了在上海地区自然干燥环境条件下不同砌块墙面、朝向、砌块深度等对砌块含水率变化的影响。研究表明,该方法测试结果可信、操作方便,可用于现场快速检测。