Location and calculation-free node-scheduling schemes in large wireless sensor networks

In wireless sensor networks that consist of a large number of low-power, short-lived, unreliable sensors, one of the main design challenges is to obtain long system lifetime without sacrificing system original performance (sensing coverage and sensing reliability). To solve this problem, one of the potential approaches is to identify redundant nodes at the sensing interface and then assign them an off-duty operation mode that has lower energy consumption than the normal on-duty mode. In our previous work [J. Wireless Commun. Mobile Comput. 3 (2003) 271; Processing of ACM Wireless Sensor Network and Application Workshop 2002, September 2002], we proposed a node-scheduling scheme, which can provide a 100% sensing coverage preservation capability. This, however, requires each node to be aware of its own and its neighbors’ location information. Also, in that scheme, each node has to do accurate geometrical calculation to determine whether to take an off-duty status. In this paper, we propose and study several alternative node-scheduling schemes, which cannot completely preserve the original system coverage, but are nonetheless light-weighted and flexible compared with the previous one. Our simulation results compare these schemes with the previous one and demonstrate their effectiveness.     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

Influence of the Temperature of a Body on Its Weight

The physical preconditions are considered for the temperature of a body to influence the force of gravity experienced by it. The results are given of experiments on weighing metal rods heated by ultrasound which confirm a dependence of the weight of the rods on their temperature.     

A generalized equation for the prediction of melting temperatures of homopolymers and copolymers

A generalized equation was derived to calculate the melting temperatures of homopolymers and copolymers. The Gibbs‐Thomson equation for homopolymers and a modified application to copolymers were derived using the proposed equation. The melting temperature T_m⁰ in the Flory equation corresponds to the melting temperature T_m^C,∞ of copolymer crystals with stems of infinite length. Also, T_m^C,n*, the melting temperature for copolymer crystals with stems containing the maximum possible number of structural units, n*, should be used instead of T_m⁰ as the basis of supercooling in crystallization. The proposed equation shows good agreement with experimental data for α‐alkene‐ethylene homogeneous copolymers.     

离体肾脏保存实验研究

本文讨论离体肾脏生存机理研究的意义和方法，研制,成功的一种携带式快速和精确控制保存环境温度的脉动灌流型人工生命维持系统，采用微处理器进行实时数据采集，处理和非线性多模式采样控制，用以维持设定的环境参数和维持最佳生存条件，本文是采用猪肾为实验材料，进行多例离体猪肾的保存实验，研究有关环境参数和保养液成分对保存效果的影响，取得良好结果，实验性猪同种异体移植亦已获得初成成功。     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

余热利用系统多目标优化模型及应用

以炭黑生产中的余热利用系统为背景建立了余热利用系统多目标优化规划数学模型;阐述了模型的求解方法;给出了实例分析。     

Selective area epitaxy of CdTe

We have performed selective area epitaxy (SAE) of CdTe layers grown by molecular beam epitaxy using a shadow mask technique. This technique was chosen over other SAE techniques due to its simplicity and its compatibility with multiple SAE patterning steps. Features as small as 50 microns × 50 microns were obtained with sharp, abrupt side walls and flat mesa tops. Separations between mesas as small as 20 microns were also obtained. Shadowing effects due to the finite thickness of the mask were reduced by placing the CdTe source in a near normal incidence position. Intimate contact between the mask and the substrate was essential in order to achieve good pattern definition.