Application of functionalised carbon nanotubes immobilised into chitosan films in amperometric enzyme biosensors

A new approach for building a bio-conductive interface for enzyme immobilisation is described. This strategy permits very simple preparation of the enzyme biosensor and also reveals direct electron transfer features. A graphite-epoxy resin composite (GrEC) electrode modified with functionalised multi-wall carbon nanotubes (MWCNTs) immobilised by 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide together with N-hydroxysuccinimide (EDC–NHS) in a chitosan (Chit) matrix was prepared and characterised by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in the presence of hexaammineruthenium (III) chloride. It was then used as a base for glucose oxidase (GOx) immobilisation by the simple method of crosslinking with glutaraldehyde (GA) with bovine serum albumin (BSA) as carrier protein. The resulting mediator-free biosensor was applied to the determination of glucose in amperometric mode at different applied potentials and the mechanism of reaction was also investigated by cyclic voltammetry, with and without dissolved oxygen in solution. Analytical parameters, as well as reproducibility, repeatability and stability were determined. Interferences were assessed using different compounds usually present in natural samples, such as wines, juices or blood, in order to evaluate the selectivity of the developed biosensor. The novel combination of carbon nanotubes immobilised with chitosan crosslinked with EDC–NHS and glucose oxidase immobilised by crosslinking with glutaraldehyde offers an excellent, easy to make biosensor for glucose determination without interferences.     

食用级碱式碳酸镁生产工艺研究

研究了以工业级硫酸镁为原料生产食用级碱式碳酸镁的工艺条件及影响产品收率的主要因素。     

聚乙烯／膨化石墨导电复合材料的研究

研究了不同的工艺条件对聚乙烯/膨化石墨导电性能和力学性能的影响。结果表明，溶液插层法具有较低的导电渗滤阈值，但其力学性能也较差。     

P_2O_5填充的PVDF复合聚合物导电膜的研制与性能研究

以聚偏氟乙烯为基质,加入适量的P2O5,制备了P2O5填充的PVDF复合聚合物质子导电膜,采用交流阻抗谱的方法研究了P2O5的质量分数不同的复合膜的导电性能及相对湿度对电导率的影响.结果表明,该电解质的室温电导率达到10-2 S·cm-1,相对湿度在20%～90%范围内,对电解质的导电性影响不大.     

碳纤维镀镍

碳纤维是一种新型的高强度、高模量材料,具有良好的导电能力.以镀镍碳纤维增强的复合材料具有高的比强度、比模量、比刚度和良好的高温性能及尺寸稳定性.本文介绍了碳纤维表面化学镀镍及电镀镍的原理和工艺流程,其中镀前预处理对整个施镀过程至关重要.化学镀镍除Ni-P体系外还有Ni-B体系.     

SHS结合热压制备TiC-Al2O3/Fe-Al复合材料

以天然钛铁矿、铝粉和石墨为主要原料,采用自蔓延高温合成技术、铝热还原法并结合热压烧结技术,制备出TiC—Al2O3／Fe—Al复合材料．研究表明：预热时间少于120s时,预热时间越长,反应燃烧波速度越大,当预热时间继续增大,对反应燃烧波速度的影响不再显著;加入添加剂Y2O3为0．2％时,金属相较均匀地弥散分布在陶瓷颗粒周围．晶粒尺寸约为2～3μm,复合材料的相对密度达到94％,抗弯强度和硬度分别为599．29MPa、83．7HRA．     

C/Cu(Fe)复合材料制备工艺及性能研究

利用三步电沉积法制备C／Cu（Fe）复合材料预制丝，将预制丝缠绕成毛坯，采用真空热压法制备C／Cu（Fe）复合材料．研究表明，真空热压工艺对复合材料力学性能有很大影响，通过力学性能试验和对拉伸断口形貌的分析，得出了制备C／Cu（Fe）复合材料的最佳工艺．     

The growth of γ-LiAlO2 layer with a highly-preferred orientation on (0001) sapphire

Using vapor transport equilibration (VTE) technique we succeeded in the fabrication of single-phase γ-LiAlO2 layer on (0001) sapphire substrate. X-ray diffraction indicated that the as-fabricated layer was highly textured with [100] orientation at proper VTE treatment temperature range from 1050℃ to 1100℃. The main factors affecting the quality of the γ-LiAlO2 layer were investigated by SEM and transmission spectra. These results reveal the possibility of fabricating γ-LiAlO2 (100)// sapphire (0001) composite substrate for GaN-based epitaxial film by VTE.     

陶瓷基复合材料伪半固态触变成形及其在卫星角框件中的应用

提出了陶瓷基复合材料伪半固态成形工艺,并应用该工艺制备了30%(体积分数)Alp/SiCp复合材料卫星角框件.通过金相分析、拉伸等实验方法验证该工艺的可行性.结果表明,该工艺成形的零件微观组织比较均匀;硬度较高,HV可达到6.43GPa;应变(ε)约为0.5%;抗拉强度(σt)约为300MPa.