40000m~3/h空分设备主换热器的设计及制造

通过对进口 4 0 0 0 0m3 /h空分设备主换热器进行结构分析及对比模拟计算 ,用国产传热翅片进行设计、采用真空钎焊工艺制造的主换热器 ,经并网运行 ,设计指标优于原空分设备 ,为今后成套大型空分设备板翅式换热器国产化设计、制造创造了条件。     

离心式空压机轴承技术改造

针对离心式空压机各级轴振动值超标的现象进行技术攻关,解决了制约装置安全平稳生产的瓶颈问题。     

大型空分设备循环冷却水处理方法的对比研究

武钢氧气公司在大型空分设备循环冷却水系统中,采用化学法和物理法进行水处理效果的实践探索,从原理和监测数据上进行了对比、分析研究,确认物理法具有高效除垢、防垢、杀菌灭藻、缓蚀以及净化等功能,可以取代化学法进行循环水处理。     

空分设备的氪氙预浓缩技术

大型空分设备的工艺流程不同，采取的氪、氙预浓缩技术也不同。介绍了适用于不同流程的从液氧中提取氪-氙浓缩物和从富氧液空中提取氪-氙浓缩物的氪、氙预浓缩工艺原理、技术参数和特点。     

漫谈钢铁企业用空分装置的流程选择

钢铁企业的氧气厂要深入了解本企业的用氧情况及周边市场的需要，据此确定拟新增空分装置的设计参数，选定最适宜的空分流程。探讨了空分流程选择时要考虑的几个方面。介绍了一种对空分装置的投资和长期运行费用之间进行经济性分析的定量计算公式，并得出了四点结论。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

一体化工作站在大气污染监测系统的应用

介绍工业污染源大气污染物排放连续监测系统的系统结构和应用范围。重点讨论一体化工作站在此系统中实际应用和性能特点。     

Heat transfer mechanism of a swirling impinging jet in a stagnation region

Heat transfer characteristics of a swirling impinging jet have been experimentally examined using a combined particle image velocimetry (PIV) and laser‐induced fluorescence (LIF) technique for simultaneous measurement of velocity and temperature fields. The present study shows that the radial width of the jet stretches with increasing swirl intensity, and that the stretching phenomenon contributes to the maximum local heat transfer coefficient. At the stagnation region, the flow near the heated surface is mixed intermittently by reverse flows toward upstream, and spatial distributions of temperature are correlated with instantaneous velocity vector maps. The dynamic behavior of recirculation zones, attributed to swirl number Sw and impinging distance, mainly determines the turbulent heat transfer at the stagnation region. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(8): 663–673, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10120     

以外供液氮替代膨胀机的深度冷冻循环

介绍空分制氮装置采用膨胀机循环与液氮循环的两种工艺流程及能量平衡 ,示出了两种循环的实例比较。指出外供液氮可以作为冷源替代膨胀机 ,且单耗低、操作更方便 ,设备维护量更小、氮气提取率更高     

济钢120t转炉二次烟气除尘设计

济钢120t转炉二次烟气除尘设备选用长袋低压脉冲除尘器,风机采用液力偶合器,并设计将加料系统除尘风量直接加入转炉二次烟气除尘系统。系统投产后,每炉钢节电1200kW,烟气排放浓度为47mg/m3,烟气温度在110℃以下。实践证明,该系统具有节能、捕集率高、排放浓度低、自动化程度高等特点。