船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

掺杂对低压ZnO压敏陶瓷材料显微结构及性能的影响

本文探讨了多种金属氧化物对ＺｎＯ－Ｂｉ＿２Ｏ＿３－ＴｉＯ＿２系材料的改性作用和对其微结构的影响，为得到预定性能的材料提供了掺杂方面的实验依据。     

基于DSP的空间电压矢量控制的变频系统设计

介绍了电压空间矢量技术的基本原理和数字信号处理器TMS320F240的基本结构，并讨论了基于TMS320F240的变频调速系统的软硬件设计，提出了一般性的结论。     

群时延精确设计的全差分四阶Bessel滤波器

采用MOS管有源电阻,提出了一种全差分R-MOSFET-C四阶Bessel有源低通滤波器,.通过调节工作于亚阈值区的CMOS管的沟道导纳补偿电阻值的大小,能抵消集成电路制造工艺中电阻值的一致偏差,实现Bessel有源滤波器群时延的精确设计.根据无源滤波器的状态方程完成有源滤波器的综合,应用3.3V,0.5μm CMOS工艺完成了群时延大小为0.75μs的四阶Bessel低通滤波器的管极计算机仿真,仿真结果表明所提电路正确有效,适于全集成.     

Thermography of aged contacts of high voltage equipment

New developments in diagnostic tools and systems are necessary for a reliable and economic evaluation of the condition of equipment in power systems. In a research project a tool for the condition of contacts of centre break disconnector, which is used under normal operation by the aid of a thermography measurement system, has been developed. In this paper, an overview about the laboratory investigation of the temperature load behaviour and the environmental influence on-site for new and aged disconnector contacts are given. A condition evaluation tool for contacts, which was the aim of the project, has been created. The basic method for the evaluation is presented, and also two additional easements for a fast identification of suspect contacts are presented. With this evaluation tool and the usage of a thermography based measuring system, a condition based maintenance strategy can be applied, whereby an early detection of damages is possible and so power quality and reliability increase.      

SiGe HBT基区结构的优化对欧拉电压的影响

欧拉电压是SiGe HBT一项重要的直流参数,受到基区结构(如Ge组分)的影响。研究发现,高温过程会导致硼的外扩散,从而影响异质结的位置,使欧拉电压受到影响。实验发现,通过优化基区结构,加厚CB结处i-SiGe厚度,可获得VA=520 V,βVA=164,320 V的SiGe HBT。     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.