Protein Extraction from Heat-stabilized Defatted Rice Bran: II. The Role of Amylase, Celluclast, and Viscozyme

ABSTRACT: The effectiveness of 3 carbohydrases for protein extraction from heat-stabilized defatted rice bran (HDRB) was evaluated. Amylase, viscozyme and celluclast extracted a maximum of 45.4, 12.1, and 28.5% protein, respectively. Further study showed that extracted protein ranged from 9.5 to 58.4% under conditions of water to bran ratio (5:1 to 20:1), α-amylase (0 to 110000 units/10 g rice bran), temperature (35 to 55 °C), and time (1 to 8 h). The maximum protein extracted was 58.4% with a water to bran ratio of 17:1, 87637 units amylase, and 50.9 °C. These results suggest that impure food-grade amylase containing protease is more effective than celluclast and viscozyme in protein extraction from HDRB.     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

SUPMAX500系统在锅炉控制系统中的应用

针对动力厂35t/h锅炉的工艺控制要求，选用SUPMAX500集散控制系统。介绍了系统的软、硬件构成及其具体实施方法。     

Experimental Research on Erbium-doped Superfluorescent Fiber Source

The effects of the variations in fiber length, fiber mirror reflectance on efficiency and output power are experimentally investigated for erbium-doped double pass backward superfluorescent fiber sources (SFSs). The influence of fiber length on mean wavelength stability (MWS) has also been demonstrated. By incorporating a short section of un-pumped erbium-doped fiber (EDF) at the output port, the pump power dependent on MWS becomes independent of pumped EDF length. This is a novel phenomenon that hasn‘t been reported up to now,and should be helpful to SFS fabrication and theory analysis. By using a fiber Michelson interferometer as spectrum slicing component,a multi-wavelength fiber source (MWFS) with ～20 channels (from 1542nm to 1559nm) is got. The MWFS has a channel spacing of ～0. 8 nm which satisfies ITUstandard. The intensity fluctuation among channels is less than 0.5dB,and the extinction ratio of all channels is above 14dB. This kind of MWFS should be useful to wavelength division multiplexing systems.     

Boiling: Size Distribution of Bubbles as Demanded by the Principle of Maximum Information

The principle of maximum informational entropy is used to find the probability density function for the departure radius of a bubble in boiling on a solid surface. A general relation is derived, which leads to particular expressions.     

The Influence of Surfactant on the Surface Characterization of Celestite in Spherical Oil Agglomeration

This study investigates the relationship between the critical surface tension of wetting of celestite and agglomeration recovery as well as the zeta potential in dependence of pH and amount of collector (Na‐Oleate). For this purpose, effects of pH and collector amount on the agglomeration recovery are investigated and zeta potential measurements and Fourier Transform Infrared Spectrophotometer (FTIR) analyses are carried out to determine the adsorption type of Na‐Oleate on celestite surface. The sessile drop technique is used for the measurement of contact angle and determination of the critical surface tension of wetting (Y_C) of celestite. The maximum agglomeration recovery is obtained at pH 7. The critical surface tension of wetting of celestite is very close to the surface tension of kerosene, which is 25.95 mN/m. Furthermore, at the optimum Na‐Oleate amount of 10 kg/ton, the critical surface tension of wetting of celestite is approximately equal to the surface tension of kerosene.     

Coupling of free surface and groundwater flows

In this paper we present some preliminary results about the coupling of shallow water equations for free surface flows and Darcy equation for groundwater flows. A suitable set of interface conditions is discussed: the Beavers and Joseph formula for the bottom stress is used. An iterative algorithm to solve the coupled problem is proposed and some numerical results are presented.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.     

含V、N无缝钢管表面外折缺陷产生原因的分析

通过对鞍钢生产的部分批号V、N微合金强化无缝钢管及生产该钢管的原料连铸坯和连轧管坯的表面缺陷进行研究，分析了含V、N钢管表面外折缺陷的成因，提出了改善钢管表面质量的方法。采用改进后工艺生产的无缝管，其表面外折废品量大幅度降低。