Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Thermodynamic state of reinforced interpenetrating polymer networks

The free energies of mixing of two networks in the interpenetrating polymer network based on crosslinked polyurethane and poly(ester acrylate) have been determined by the vapour sorption method. It was established that the constituent networks in the IPN are not miscible. The introduction of fillers of different chemical nature increases the compatibility. The thermodynamic affinity of the fillers to the individual networks and IPN was estimated. It was established that when the free energy of interaction of one or both components of the IPN with the filler is negative, reinforcement leads to the formation of a compatible and equilibrium system. For fillers having no affinity to the polymers, compatibilization is observed, which is connected with slowing down of phase separation in the system in the presence of filler.     

中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

用两亲聚合物制备大颗粒苯丙乳液

分别以两亲聚合物P(C9-AA)和P(DCPD-St-α-St-AA)作乳化荆，研究了制备大颗粒(约1μm)及具有一定稳定性的苯丙乳液的方法，讨论了乳化剂，温度及引发剂用量对乳液性能的影响。结果表明，以P(C9-AA)作乳化剂时，引发剂用量为单体质量的1．2％，90℃时可以合成性能良好的苯丙乳液；以P(DCPD-St-α-St-AA)作乳化荆时，引发剂用量为单体质量的1．2％，80℃时可以合成性能良好的苯丙乳液。     

An Electron Spin Resonance Study of Evolution of Organic Free Radicals in Irradiated Pepper During Heat Treatment

ABSTRACT: The thermal evolution behavior of the organic free radicals induced in irradiated black pepper was studied by electron spin resonance spectroscopy. To analyze the time-dependent evolution process, we used the theory of transient phenomena, that is, an ordinal differential equation, as well as the nonlinear least squares numerical method. We found that the radical evolution that occurred in the irradiated pepper obeys a single exponential function and yields a unique time constant. The evolution of the organic free radical undergoes a simple reaction process of a single radical species.     

砌筑砂浆达不到设计要求的事故原因分析

从砂浆的配合比、和易性、原材料等对砌筑砂浆达不到设计要求的事故原因进行了分析。     

疏水缔合型聚丙烯酰胺的合成与性能评价

为了提高高相对分子质量的聚丙烯酰胺的抗温抗盐性能,利用自制的两亲表面活性单体与丙烯酰胺共聚合成了疏水缔合型聚丙烯酰胺并进行室内评价。结果表明,在高温、高盐、高钙条件下,合成的疏水缔合型聚丙烯酰胺具有良好的增粘性和较强的热稳定性;克服了疏水缔合型聚合物在盐水中溶解性差的问题,可用各种矿化度的盐水和油田产出污水配制;具有良好的无机盐增粘性能和抗温性能。     

PAN聚合物一次性溶解新技术

阐述了一个全新的聚丙烯腈高聚物溶解理论，取代了以往人们思维中的高聚物大分子必须经过先溶胀再溶解的漫长的静态溶解过程。对于年产50kt/a腈纶装置可减少一次性投资约1500万元，减少运转费用360万元／a，在现有腈纶大装置上实施，经济效益十分可观。     

氯碱生产中的腐蚀与防护

介绍了氯碱装置中介质的腐蚀特性、常用材料的耐腐蚀特性及应用实例。     

PLC在原料系统的应用

阐述了硅铁生产中焦碳生产输送系统的工作原理和工艺要求，介绍了PLC在原料输送系统中的应用，给出了PLC的I／O接线图及程序框图，提出了工业原料生产输送控制系统的设计特点。