基于Legendre多项式的随机连续系统的Markov参数估计

本文在讨论连续Ｗｉｓｅｎｒ过程的Ｌｅｇｅｎｄｒｅ多项式逼近值的相关性和Ｗｉｅｎｅｒ过程扰动下连续线性系统基于该正交多项的最小二乘估计有偏性后，提出了无偏一致的且数估计误差方差最小的Ｍａｒｋｏｖ估计（最小方差估计）算法，并给出本文方法的仿真结果。     

Valid parameter range analyses for chemical reaction kinetic models

The present work quantifies the relations between the structure of a chemical reaction kinetic model, its valid parameter range, and the truncation error tolerance of the model. General methods are presented to solve the three important problems of valid parameter range analysis: (1) identification of the valid parameter range of a kinetic model, (2) estimation of the error tolerance required when applying a kinetic model over a specified parameter range, and (3) improvement of existing model generation algorithms to construct more robust models. Finally, the relationship between a model's structure, its valid parameter range, and the truncation error tolerance are illustrated by the flexibility-tolerance-model graph. The new methods are applied to pyrolysis of methane/ethane mixtures.     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

冷弯型钢纵向变形的理论分析及计算

对冷弯型钢的纵向变形过程进行了力学分析，得到了变形微分方程，求得了转动角的理论公式，并对其变形形状进行了分析计算。     

动态矩阵控制系统稳定域的根轨迹分析

本文使用根轨迹技术从理论上分析了纯滞后工业过程参数变化对系统稳定性的影响,得到了一个与设计参数有关的稳定域,从而为设计参数自动整定提供了参考。     

Self-calibration based on invariant view recognition: Dynamic approach to navigation

We extend a dynamic approach of behavior generation to the representation of spatial information. Two levels of dynamics integrate dead-reckoning, dominant far from home bases, and piloting, dominant near home bases. When the view-based piloting system recognizes a home base, visual place information recalibrates the dead-reckoning system, inverting the hierarchical ordering of the two dynamic levels by time scale inversion. Reference views taken at discrete home bases are recognized invariantly under rotation of views. This process yields compass information. Continuous translational information is obtained as a neural place representation built from view correlations with a scattered set of local views. This self-calibrating cognitive map couples into a dynamics of heading direction integrating the behaviors of obstacle avoidance and target acquisition. Targets can be designated in terms of the cognitive map. We demonstrate the dynamical model in simulation.     

调节对象参数和运动特性随工况变化的分析

水轮机调节对象的许多参数都是随运行工况变化的。以调节对象线性化模型为基础，从1个实例计算人手，计算了不同工况下水轮机传递系数和发电机6个参数的变化情况，进而计算这些参数变化对捌节对象特征根的影响。通过汁算表明，其水力振荡衰减速度与出力有关．而系统的其他运动特性随工况变化较小。     

基于NURBS的PDE曲面构造法研究及应用

由非均匀有理Ｂ样条曲线曲面给定边界条件，用偏微分方程来构造曲面，以参数“ａ”控制其整体形状，本文分析其思路原理及过程，并列举了在ＣＡＤ上的应用，最后分析了优缺点。     

34CrMoV结构钢动态再结晶行为研究

应用Gleeble-1500热模拟实验机进行等温压缩试验,研究了变形工艺参数对34CrMoV结构钢动态再结晶行为的影响.结果表明,其流变应力随变形温度升高而降低,随应变速率提高而增大;随着应变速率的降低,应变量的增加和变形温度的升高,动态再结晶速度加快且奥氏体晶粒得到细化.     

Impacts of spectral band difference effects on radiometric cross-calibration between satellite sensors in the solar-reflective spectral domain

In order for quantitative applications to make full use of the ever-increasing number of Earth observation satellite systems, data from the various imaging sensors involved must be on a consistent radiometric scale. This paper reports on an investigation of radiometric calibration errors due to differences in spectral response functions between satellite sensors when attempting cross-calibration based on near-simultaneous imaging of common ground targets in analogous spectral bands, a commonly used post-launch calibration methodology. Twenty Earth observation imaging sensors (including coarser and higher spatial resolution sensors) were considered, using the Landsat solar reflective spectral domain as a framework. Scene content was simulated using spectra for four ground target types (Railroad Valley Playa, snow, sand and rangeland), together with various combinations of atmospheric states and illumination geometries. Results were obtained as a function of ground target type, satellite sensor comparison, spectral region, and scene content. Overall, if spectral band difference effects (SBDEs) are not taken into account, the Railroad Valley Playa site is a “good” ground target for cross calibration between most but not all satellite sensors in most but not all spectral regions investigated. “Good” is defined as SBDEs within ± 3%. The other three ground target types considered (snow, sand and rangeland) proved to be more sensitive to uncorrected SBDEs than the RVPN site overall. The spectral characteristics of the scene content (solar irradiance, surface reflectance and atmosphere) are examined in detail to clarify why spectral difference effects arise and why they can be significant when comparing different imaging sensor systems. Atmospheric gas absorption features are identified as being the main source of spectral variability in most spectral regions. The paper concludes with recommendations on spectral data and tools that would facilitate cross-calibration between multiple satellite sensors.