邻苯二甲酸丁苄酯的合成

叙述了邻苯二甲酸丁苄酯的市场应用概况．并介绍了二步合成法及一步合成法的实验操作．     

气相色谱法分析E型电热蚊香片中炔丙菊酯的含量

采用填充柱气相色谱法,选用以OV-101为固定相的玻璃柱,用内标法测定E型电热蚊香片中炔丙菊酯的含量。方法的线性相关系数为0.9999,标准偏差为0.043,变异系数为0.34%,回收范围为99.87%～100.07%。     

DOP与CPE的含量对BaSO4填充聚氯乙烯基隔音复合材料性能的影响

将邻苯二甲酸二辛酯(DOP)与氯化聚乙烯(CPE)按照不同的质量份数加入到BaSO4填充聚氯乙烯基(PVC)隔音复合材料中,探讨DOP与CPE的含量对BaSO4填充聚氯乙烯基隔音复合材料隔声性能的影响,利用BSWA VS302USB双通道声学分析仪,万能材料试验机,动态热机械分析仪测试了材料的隔声性能,力学性能,阻尼性能。结果显示:当PVC相对质量为100份,DOP为50份,CPE为20份时对低频具有较好的隔声性能,当DOP相对质量为80份,CPE为20份时对中频具有较好的隔声性能,对高频影响较小。     

酞酸二丁酯表面印迹聚合物的合成及其吸附性能

以酞酸二丁酯(DBP)作为模板分子,甲基丙烯酸作为功能单体,乙二醇二甲基丙烯酸酯(EDMA)作为交联剂,在硅胶表面合成分子印迹聚合物(MIPs)。通过红外、热重分析、比表面积测定等对聚合物进行分析和表征;采用静态吸附法对水相中的印迹聚合物的吸附性能进行考察.红外结果表明硅胶表面存在对模板分子具有识别功能的官能团;热重分析证明其良好的热稳定性;通过测定计算印迹膜厚度;静态吸附实验说明印迹聚合物具有良好的吸附性能.     

反应精馏法催化合成邻苯二甲酸二异辛酯

研究了反应精馏法催化合成邻苯二甲酸二异辛酯系列工艺条件，发现该方法有生产工艺简单，反应条件温和，反应时间短，产品中副产物少，转化率高，产品质量较好，且可以在反应的同时，对产物进行有效的分离等优点。最佳工艺条件：催化剂硫酸的用量占总投料量的3‰、釜温控制178℃、柱温控制163℃，m（苯酐）：m（异辛醇）为1：2．7，回流比为1：1，反应时间为1．5h，反应床层高度为2．7m时，邻苯二甲酸酐的转化率可达到99％。     

水源水质受DEHP污染的粉末活性炭吸附处理工艺

采用含邻苯二甲酸二(2-乙基己基)酯(DEHP)的试验水样模拟城市取水水源发生DEHP水污染事故,测定粉末活性炭(PAC)对水样中DEHP的吸附性能,考察PAC炭种、吸附时间、DEHP初始浓度和PAC投加量等因素对DEHP的吸附量和脱除率的影响。试验结果表明:木屑PAC具有较大的比表面积,对DEHP具有良好的吸附效果,适用于DEHP水污染的应急处理。应急处理一般的DEHP水污染事故,DEHP污染浓度超标10～30倍时,PAC吸附DEHP的最佳条件为:吸附时间120 min,PAC投加量为20～80 mg/L,PAC对DEHP的吸附过程符合Henry等温式。     

Determination of flonicamid and its metabolites in bell pepper using ultra-high-performance liquid chromatography coupled to high-resolution mass spectrometry (Orbitrap)

The development and validation of a method to determine flonicamid and its metabolites as TFNA (4-trifluoromethylnicotinic acid), TFNG (N-(4-trifluoromethylnicotinoyl) glycine) and TFNA-AM (4-trifluoromethylnicotinamide) in bell pepper samples by ultra-high-performance liquid chromatography coupled to Orbitrap mass spectrometry (UHPLC-Orbitrap-MS) was performed. A fast and simple extraction procedure with acidified acetonitrile and salts (magnesium sulfate and sodium chloride) was used. The methodology was validated, checking for specificity, recovery, precision, limits of detection (LODs) and limits of quantification (LOQs). The recoveries ranged from 84% to 98%, and precisions were lower than 17%. Finally, LODs ranged from 1 µg kg^–1 (flonicamid) to 6 µg kg^–1 (TFNA-AM), while LOQs ranged from 10 µg kg^–1 (flonicamid) to 30 µg kg^–1 (TFNA-AM). Bell pepper samples were analysed and concentrations up to 98 µg kg^–1 (flonicamid) were detected, although the sum of flonicamid and metabolites did not exceed the maximum residue limit (MRL) set by the European Union.     

Properties of novel diallyl phthalate resin modified with sulfur‐containing allyl ester compounds

Sulfur‐containing allyl ester, which reacts with diallyl phthalate (DAP) resin to have allyl groups, was synthesized by the reaction of allyl phthalic acid with bisphenol having sulfur atoms. The sulfur‐containing allyl ester compound was blended with DAP resin to improve the adhesive properties to copper. By modification with sulfur‐containing allyl ester compound, the T‐peel adhesive strength and the lap shear adhesive strength to copper was improved. In particular, the adhesive strength was greatly improved when the resin was modified with the allyl ester compound having a disulfide bond (?S?S?) (DADS). It is concluded that this result is due to the improvement of the interfacial adhesive strength because the sulfur atom was found to be located in the surface of the copper by Fourier transform infrared (FTIR) analysis. The glass transition temperature (T_g) and the thermal decomposition temperature (T_d) of the cured DAP resin modified with DADS slightly decreased with increasing concentration of DADS. The lowering of T_g is because the crosslinking density of the DAP resin modified with DADS is smaller than that of DAP resin. Moreover, from thermogravimetric analysis, the lowering of Td of the DAP resin modified with DADS is because DADS is likely to pyrolyze. © 2013 Society of Chemical Industry