低温导热绝缘胶粘剂研究

一种低温导热绝胶粘剂用于氢氧发动机系统表面温度传感器的端封和胶接安装，介绍了胶粘剂的技术要求，研究方案及试验结果。以DW－3超低温胶粘剂为基础，经改性设计后，仍能保持胶粘剂原有的耐低温特性，而且其导热，绝缘等性能均能满足设计和使用要求。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

Subsecond thermophysics research at the Boris Kidrich Institute Vincha

In the early eighties, at the Boris Kidrich Institute Vincha, a method for measuring specific heat and electrical resistivity of electrical conductors in the millisecond resolution range was developed for measurements from room temperature to 1900 K. Over a period of nearly 10 years, the method was applied to different materials, including pure metals, ferrous, and nickel/ chromium alloys, and to the characterization of candidate materials for thermophysical property reference standards. This paper describes the method and reviews the results obtained in specific heat and electrical resistivity studies of ferromagnetic and other materials. The paper also demonstrates capabilities of the method for describing phase transitions or anomalies in pure metals (Fe, Co, Ni) or alloys (Nichrome, austenitic stainless steel).Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

冷却速度对激光相变组织分布的影响

提出通过改变边界换热条件，从而改变冷却速度，达到控制激光相变硬化。实验和计算结果的比较表明，这种控制相变及其组织分布的方法能够处理激光淬火难以解决的问题。     

S—135钢板热轧工艺研究

S—135钢板是水电站用高强耐磨不锈钢板,既要求强度高、韧性好,又要求耐磨、耐蚀性强,生产难度较大。除我厂外,目前国内尚无其它厂家能够生产这种钢板。该钢板在加热轧制,冷却过程中要解决很多技术难点。我们通过采用特殊的控制轧制和控制冷却工艺,很好地解决了诸多技术难点,使S—135钢板的开发研制取得了成功。为电站用高强度耐磨不锈钢生产提供了宝贵的经验,也为控制轧制及控制冷却技术在中板生产行业的应用起到了积极的推动作用。     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

溶胶－凝胶二氧化硅驻极体薄膜的物理化学改性

实验研究了由溶胶－凝胶法制备二氧化硅驻极体薄膜的工艺。用红外透射谱、扫描电子显微镜以及驻极体等温表面电位测量和热刺激放电等实验考察了热处理和化学表面修正两个关键工艺对溶胶－凝胶二氧化硅样品驻极体性能的影响。结果表明经过高温条件下一定时间的热处理和化学表面修正，可以制备出性能优良的驻极体薄膜     

热电厂锅炉运行技术指标的微机管理

本文从锅炉运行技术指标台帐微机管理的实际出发，提出了热量计算中主蒸汽流量修正系数Ｃ和给水焓值Ｚ两项参数回归的计算公式，提高了热量计算数值精度。