Fast Hybrid Approach for Texturing Point Models

We present three methods for texturing point models from sample textures. The first method, the point parameterization method, uses a fast distortion‐bounded parameterization algorithm to flatten the point model's surface into one or more 2D patches. The sample texture is mapped onto these patches and alpha blending is used to minimize the discontinuity in the gaps between the patches. The second method is based on neighborhood matching where a color is assigned to each point by searching the best match within an irregular neighborhood. The hybrid method combines the former two methods, capitalizing on the advantages of both. The point parameterization method is used first to color most of the points, and the point neighborhood‐matching method is then applied to the points belonging to the gaps between the parameterized patches to minimize the discontinuity. We opt for fast texture generation, while some discontinuities may appear in the gaps of anisotropic textures.     

Treatment of Point Defects in Nanowire MOSFETs Using the Nonequilibrium Green’s Function Formalism

A program to numerically simulate point defects in nanowire metal-oxide-semiconductor field-effect transistors is described. The simulation scheme is based on the non-equilibrium Green’s function method self-consistently being obtained via the resolution of 3D Poisson’s equation. A tight-binding hamiltonian is used and the point defect is characterized by a macroscopic coulombic tail treated in the mode-space approach, plus a short range on-site perturbation potential energy, treated exactly. The effect on internal quantities and on the transistor characteristics is studied as a function of the strength and the location of the defect potential. Subthreshold current is found to vary in a factor 10 according to the position of the impurity.Also With Institut Universitaire De France (IUF).     

Quantum Lattice-Gas Automata Simulation of Electronic Wave Propagation in Nanostructures

We report the two- and three-dimensional quantum lattice-gas automata simulation for one-particle electronic wave propagation in nanostructures. The transmission coefficient of the electronic wave through the two-dimensional quantum point contact is investigated taking account of the surface roughness of the confinement wall. It is demonstrated that the electron transmission is significantly affected by the surface roughness pattern even if the same roughness parameter is assumed. We also perform the three-dimensional simulation, and the wave propagation in the structure like an ultrathin-body MOSFET is visualized.     

利用红外测温诊断技术发现电流互感器内部缺陷

在电力系统中，电力设备的质量直接关系到电网的运行安全，而由于电力设备内部缺陷而引起的设备事故对电网的危害更大。应用红外测温诊断技术可以及时发现电力设备缺陷特别是内部缺陷，使设备故障得到及时的消除，避免电力系统事故的发生。     

椭圆曲线密码系统(ECC)整体算法设计及优化研究

在安全性差不多的情况下,ECC使用的密钥要比RSA短得多.然而,虽然ECC的数学理论已比较成熟,但其算法要比RSA更难理解,算法实现也比RSA困难得多,往往需要通过专门的硬件来加速算法实现.本文设计了一种ECC整体算法,并对其中的点积、平方剩余判定等关键算法进行优化,提高了算法的效率,使其能够完全通过软件实现.     

恒温恒湿系统最佳除霜时刻控制的研究

针对于恒温恒湿系统的除霜最佳时刻的研究,本文提出了在户外温湿度恒定,室内温湿度变化状况下,当蒸发器表面上所结的霜的面积达到蒸发器总换热面积的75%时,利用此时的冷凝压力与蒸发压力的比值作为对机组除霜指令发出的基准.经实验的验证此方法还是可行的,能够运用于实际的工业恒温恒湿机组的最佳除霜时刻控制.     

遥测法获取建筑物立面图

作为建筑物数字化建设的一项重要内容,建筑物立面图可以通过多种测绘方法获得。研究了普通测量设备条件下测绘建筑物立面图的方法,提出了建立控制基线,遥测获取建筑物特征点三维坐标并通过坐标变换,最终获取立面图的手段,结合非量测相机,采用一种近似但较简洁的解析方法对建筑物细部图形要素进行了提取。同时对建筑物特征点采集数据中可能出现的粗差,提出了检查和评判的方法。实践证明本方法具有简洁、实用的特点。     

液氮冻制冰套法对水三相点温度的影响

介绍了液氮作为冷却剂在水三相点容器内冻制冰套的方法。利用该方法同时在两个不同真空度的水三相点容器内分别冻制冰套。通过实验，研究了此方法对所复现的水三相点温度的影响。实验结果表明：冻制过程中产生的应力以及开始生成的小冰晶引起水三相点温度偏低；并且，其对水三相点温度的影响随着水三相点容器内真空度的降低而增大。随着应力慢慢消除，小冰晶逐渐长大为大冰晶，所复现的水三相点值逐渐回升并趋于稳定。因此，为了高精度复现和准确测量水三相点，采用该冻制方法时，必须将冰套老化至少5天以后，才可以消除其对水三相点温度的影响。     

转炉冶炼终点炉渣氧化性和碱度的研究

通过在实验室电阻炉上的实验研究，得出了复吹转炉在吹炼含磷较高铁水时冶炼终点最佳的炉渣氧化性和碱度。实验结果表明，渣一钢反应接近平衡时，炉渣的氧化铁含量在15％左右，炉渣碱度m(CaO)／m(SiO2)为4．4，这时炉渣的脱磷能力最强。研究的结果对于复吹转炉冶炼的终点操作是非常有益的。     

攀钢连铸坯角横裂缺陷产生的原因与对策

对攀钢Q235G钢连铸坯出现的角横裂缺陷进行了调查分析，在此基础上确定了连铸保护渣是引起角横裂的主要原因。并对保护渣的配方进行了改进，通过试验，研制出了适合攀钢普碳包晶钢用的连铸保护渣，有效地控制了Q235G钢连铸坯角的横裂缺陷。