A new method for the determination of wax precipitation from non-diluted crude oils by fractional precipitation

Wax precipitation is one of the most important flow assurance problems. Unfortunately, experimental data are very scarce to confirm existing models for prediction of such precipitation problem. This work reports a new experimental method. Multistage fractional wax precipitation was carried out by decreasing the temperature of crude oil. No solvent dilution was used, so the effect of solvent on temperature wax precipitation was avoided. The reproducibility of the method was tested with comparable results. The precipitation curve and the wax appearance temperature were obtained for two crude oils with different chemical nature using the reported method.     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

Synthesis of polymeric pour point depressants for Nada crude oil (Gujarat,India) and its impact on oil rheology

Five flow improvers have been synthesized to study rheological properties of Nada crude oil (Gujarat, India). Anhydride copolymers were prepared making use of the copolymerization of acrylates of different alkyls with maleic anhydride and the Poly (n-alkyl acrylates-co-N-hexadecylmaleimide) were prepared by the reaction of copolymer with hexadecylamine. The additives were purified and characterized by FTIR, GPC. The prepared polymeric additives shows dual function both as wax dispersants and flow improvers and all of them acts as good pour point depressants. Yield stress and the viscosity of the crude oil at different temperatures and concentrations of additives were evaluated by zero friction advanced rheometer AR-500 of TA instrument. Comparison of morphologies and structures of wax crystals or aggregates in waxy crude oils beneficiated with and without a PPD was also done by micro photographic studies which show the modification in wax crystal morphology due to additives.     

基于ANSYS的铸嘴流体耦合场三维有限元仿真分析

作者用大型有限元分析软件ANSYS对铸嘴内稳态层流铝熔体进行仿真分析。实现了三维建模。解决了三维热一流耦合求解的问题，得到铝流体的速度、压力及温度的分布图。分析了铸嘴出口速度和温度的分布规律及其对连续铸轧的影响。     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

Managing nutrient losses from rural point sources and urban environments

Nutrient loss from rural point sources and urban environments need to be minimised as part of strategies to overcome declining water quality on the Swan Coastal Plain and in the Peel-Harvey estuary in Western Australia. This paper discusses the management of nutrient losses from domestic effluent, urban stormwater runoff, domestic gardens and public open space, intensive animal industries and intensive irrigated agriculture. Measures to minimise nutrient losses from these sources are outlined, using cooperative, technological and regulatory approaches.