国内外聚乙烯管材树脂生产现状

介绍国内外聚乙烯管材料的开发和生产情况,以及聚乙烯管材树脂的主要生产厂家。     

茂金属线型低密度聚乙烯的加工性能

采用齐聚-共聚复合催化剂合成出了相对分子质量分布指数大于4的原位共聚线型低密度茂金属聚乙烯(mLLDPE)。流变实验结果表明,mLLDPE具有切敏性和非温敏性。改性实验结果表明,向100质量份mLLDPE中加入5质量份氟母粒,或10质量份LDPE,或2质量份氟母粒和5质量份LDPE,可使mLLDPE的加工流动性能获得改善,聚合物的机械性能不会发生明显降低,可用常规加工设备加工。加工成型实验结果表明,使用65型管材挤出机和TDL-12L中空成型机,以氟母粒-LDPE复合改性mLLDPE为原料,可生产出内、外表面均光滑的32管材和10L中空容器,挤出过程稳定。     

Estimating crystallinity in high density polyethylene fibers using online Raman spectroscopy

Online Raman spectra, obtained at different points along the spin line during pilot‐scale nonisothermal melt spinning of high density polyethylene (HDPE) fibers, are presented for the first time. The fraction of the crystalline phase corresponding to each spectrum was determined from the normalized integrated intensity of the 1418 cm^?1 Raman band. It is well established that this band represents the orthorhombic crystalline phase in polyethylene. The estimates of percent crystallinity obtained from decomposition of the Raman spectrum were compared with the percent crystallinity from differential scanning calorimetry (DSC) measurements. It is concluded that online Raman spectroscopy can be successfully used to monitor the development of crystallinity in HDPE fibers as a function of distance from the spinneret. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 545–549, 2003     

Mechanical properties of polyethylene mixtures crystallized under high pressure

The mechanical properties of a medium molecular weight polyethylene (MMW‐PE) and an ultrahigh molecular weight PE (UHMW‐PE) binary mixture with different weight fractions crystallized from the melt at 0.1 and 450 MPa were studied. The tensile modulus, yield stress, and strain were obtained as a function of the weight fractions in the PE mixtures at 25 and 85°C. The tensile modulus in the sample crystallized at 0.1 MPa decreased from 1.5 GPa of pure MMW‐PE to about 0.4 GPa of pure UHMW‐PE with the UHMW‐PE content but it did not decrease with the UHMW‐PE in the sample crystallized at 450 MPa in testing at 25°C. A decreasing rate of the storage modulus E′ of UHMW‐PE in a dynamic measurement for the sample crystallized at 0.1 MPa with the temperature is larger than that of the sample crystallized at 450 MPa. These experimental facts are interpreted in relation to the molecular motion and crystallinity of the sample. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1962–1968, 2003     

1H T2‐NMR monitoring of crosslinked polyolefin aging

This work examines the correlation between the ¹H‐NMR T₂ relaxation constant and the mechanical properties of aged crosslinked polyolefin cable insulation. T₂ experiments on unswollen samples could not differentiate between unaged and highly aged materials; all exhibited ¹H T₂ constants of approximately 0.5 ms. To accentuate the effects of aging, samples were swollen in various solvents. Unaged samples had T₂ values of approximately 15 ms in good solvents. With thermal aging, T₂ values decreased as the ultimate tensile elongation decreased. However, the correlation between T₂ and elongation differed for samples irradiated with high‐energy radiation and for materials aged above versus below the crystalline melting temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2578–2582, 2003     

载体比表面积及孔径对Nb_2O_5/α-Al_2O_3催化剂酸性及反应性能的影响

采用浸渍法制备了Nb2O5/α-A l2O3催化剂(简称催化剂)并用于环氧乙烷水合制乙二醇的反应,通过控制α-A l2O3载体中致孔剂的含量来调变载体的孔径、孔分布及比表面积;采用吡啶吸附红外光谱、氨程序升温脱附法研究了载体的比表面积及孔径对催化剂酸性及反应性能的影响。实验结果表明,产物的选择性受扩散因素及催化剂酸性的影响,而催化剂的酸量、酸密度可以通过载体的孔径及比表面积的变化加以调控。比表面积较小及孔径较大的载体对催化剂催化环氧乙烷水合制乙二醇的反应较为有利。当载体的比表面积小于0.80m2/g、孔径为4.00~8.00μm时,在反应温度160℃、反应压力1.5M Pa、n(H2O)∶n(EO)=22、液态空速25h-1的条件下,环氧乙烷的转化率大于99.8%,乙二醇的选择性超过89.9%。     

Phase behavior,density, and crystallization of polyethylene in n‐pentane and in n‐pentane/CO2 at high pressures

The phase behavior and volumetric properties of polyethylene (PE) in solutions of n‐pentane and n‐pentane/CO₂ were studied in a temperature (T) range of 370–440 K at pressures up to 60 MPa. Measurements were conducted with a variable‐volume view‐cell system equipped with optical sensors to monitor the changes in the transmitted light intensity as the P or the T of the system was changed. Lower‐critical‐solution‐temperature‐type behavior was observed for all of the liquid–liquid (L–L) phase boundaries, which shifted to higher pressures in solutions containing CO₂. The solid–fluid (S–F) phase boundaries were investigated over a P range of 8–54 MPa and took place in a narrow T range, from 374 to 378 K in this P interval. The S–F phase boundary showed a unique feature in that the demixing temperatures showed both increasing and decreasing trends with P depending on the P range. This was observed in both the PE/n‐pentane and PE/n‐pentane/CO₂ mixtures. The density of these solutions were measured as a function of P at selected temperatures or as a function of T at selected pressures that corresponded to the paths followed in approaching the phase boundaries (S–F or L–L) starting from a homogeneous one‐phase condition. The data showed a smooth variation of the overall mixture density along these paths. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2201–2209, 2003     

溶剂对环氧乙烷催化水合制乙二醇的影响

研究了NY催化剂催化环氧乙烷水合制乙二醇(EG)过程中,溶剂、催化剂添加量和水与环氧乙烷的摩尔比(简称水比)对EG选择性的影响。实验结果表明,以丙三醇作为溶剂使催化剂进行循环,能提高EG的选择性,效果好于以生成的EG作为溶剂循环催化剂。催化剂添加量、水比和溶剂添加量对EG选择性具有较大影响,其中溶剂添加量对EG选择性的影响最显著。在低水比(1.0~4.0)条件下,EG质量分数小于30%、催化剂质量分数大于7.2%时,EG选择性稳定在95.63%~97.92%,平均值为96.80%,此结果对于进一步降低EG合成工艺的能耗具有指导意义。     

HDPE／PS／HDPE－g－PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ⅰ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ、ＤＳＣ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高     

超高分子量聚乙烯的辐照效应

通过密度测定和ＤＳＣ热分析，观测了超高分子量聚乙烯的辐射效应。实验结果表明：在吸收剂量０—１．１３ＭＧｙ范围内，密度随吸收剂量的增加而增大，熔化热和熔点也有所增加，特别是在低剂量范围内增加十分明显。以上结果都说明，超高分子量聚乙烯在辐照过程中，结晶在完善或有新的结晶形成