Synthesis and thermal properties of block copolyetheresters with poly(pentamethylene p,p′-bibenzoate) segments

The block copolyetheresters with hard segments of poly(pentamethylene p,p-bibenzoate) and soft segments of poly (tetramethylene ether) were prepared by melt polycondensation of dimethyl-p,p-bibenzoate, 1,5-pentanediol and poly (tetramethyene ether) glycol (PTMEG) with molecular weights of 650, 1000 and 2000. The results by NMR indicate that the polymer composition is determined by the charge molar ratio (x) of PTMEG to dimethyl-p,p-bibenzoate. The thermal transitions of the block copolyetheresters were investigated by DSC in combination with X-ray diffraction and polarized microscopy. Some block copolyetheresters exhibit a monotropic smectic phase due to the presence of the poly (pentamethylene p,p-bibenzoate) segments. As the molar content of PTMEG increases, the average sequence length of the polyester segments decreases, the isotropic-smectic transition temperature and the smectic order decrease accordingly. When x is as high as 0.3, the block copolyetheresters exhibit no liquid crystallinity.     

Synthesis and characterization of new flame‐retardant poly(amide‐imide)s containing phosphine oxide and hydantoin moieties in the main chain

Six new flame‐retardant poly(amide‐imide)s (PAIs) 9a–f with high inherent viscosities containing phosphine oxide and hydantoin moieties in main chain were synthesized from the polycondensation reaction of N,N′‐(3,3′‐diphenylphenylphosphine oxide) bistrimellitimide diacid chloride 7 with six hydantoin derivatives 8a–f by two different methods such as solution and microwave assisted polycondensation. Results showed that the microwave assisted polycondensation, by using a domestic microwave oven, proceeded rapidly, compared with solution polycondensation, and was completed in about 7–9 min. All of the obtained polymers were fully characterized by means of elemental analysis, viscosity measurements, solubility test, and FTIR spectroscopy. Thermal properties and flame retardant behavior of the PAIs 9a–f were investigated using thermal gravimetric analysis (TGA and DTG) and limited Oxygen index (LOI). Data obtained by thermal analysis (TGA and DTG) revealed that these polymers showed good thermal stability. Furthermore, high char yields in TGA and good LOI values indicated that these polymers are capable of exhibiting good flame retardant properties. These polymers can be potentially utilized in flame retardant thermoplastic materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5062–5071, 2006     

Effect of the nature and degree of crosslinking on the Rose Bengal uptake by DVB‐, NNMBA‐, HDODA‐, and TTEGDA‐crosslinked aminopolyacrylamides

Polyacrylamides with 2–20 mol % divinyl benzene (DVB), N,N′‐methylene‐bisacrylamide (NNMBA), 1,6‐hexanediol diacrylate (HDODA), and tetraethyleneglycol diacrylate (TTEGDA) crosslinking and without crosslinking were prepared by free radical solution polymerization. Amino functions were incorporated into these polymers by transamidation with excess ethylenediamine. The dye uptake of nonprotonated and protonated aminopolyacrylamides was followed by batch equilibration method towards Rose Bengal (RB), Methyl Orange (MO), Methyl Red (MR), and Methylene Blue (MB). RB uptake by the polyacrylamide‐supported systems is higher than other dyes. Generally the dye uptake by the protonated systems is higher than the nonprotonated systems. To optimize the conditions of dye uptake, the effect of the concentration of RB solutions, temperature, and pH were followed. Kinetic studies showed that the uptake of RB by both nonprotonated and protonated crosslinked aminopolyacrylamides is a phase boundary process followed by three‐dimensional diffusion. The extent of RB uptake by the various systems depends on the nature and degree of crosslinking, and the relative rigidity/flexibility ofthe polyacrylamide support. Thus, the dye uptake followed the order: linear > NNMBA‐ > DVB‐ > TTEGDA‐ > HDODA‐crosslinked system. The dye uptake followed the same trend as the variation of amino capacity with degree of crosslinking in the respective crosslinked system. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and properties of polyelectrolyte complex sponges composed of hyaluronic acid and chitosan and their biological behaviors

Polyelectrolyte complexes (PECs) composed of chitosan and hyaluronic acid (HA) were prepared in various pH regions and at different weight ratios. At low pHs, there was a strong ionic interaction between NH groups in chitosan and both COO^? and COOH groups in HA due to the deprotonation of HA, whereas weak linkages were formed at high pHs because only the carboxyl groups of HA could interact with NH groups in chitosan. The formation of PECs resulted in a decrease in the crystallinity and thermal stability caused by the interactions between polyions. With variations in the degree of ionization of polyions at various pH conditions, novel PEC sponges were prepared by the freeze drying of PEC solutions. Furthermore, for the evaluation of the wound‐healing effect of PEC sponges with or without an antimicrobial agent (silver sulfadiazine), they were applied to a full‐skin defect of a Wistar rat in vivo. The histology and computerized morphometric analysis of the epidermal healing confirmed the proliferation of fibroblasts in the wound bed and a distinct reduction in infectious agents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 925–932, 2003     

Ionic conductivity and interfacial properties of polymer electrolytes based on PEO and boroxine ring polymer

Blended polymer electrolytes based on poly(ethylene oxide) (PEO) and boroxine ring polymer (BP) solvated with lithium triflate were formulated and evaluated. Compared to PEO–salt polymer electrolyte, ionic conductivities of blended polymer electrolytes were two orders of magnitude higher in a low‐temperature range; as well, lithium transference numbers were increased to ～ 0.4. These were due to the increased mobility and anion trapping of boroxine rings. BP also exhibited the stabilizing effect on lithium–polymer electrolyte interface, and a reduced interfacial resistance between lithium metal and the polymer electrolyte was found with increasing of BP content. Polymer electrolytes based on PEO and BP are suitable for use in lithium secondary battery. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 17–21, 2002; DOI 10.1002/app.10090     

Shrinking rate of conducting grains in HCl–protonated polyaniline,polypyrrole, and polypyrrole/polyaniline blends with their thermal aging

The dc electrical conductivity (σ) of HCl‐protonated polyaniline, polypyrrole, and their blends was measured from 80 to 300 K for thermal aging times between approximately 0 and 600 h. The thermal aging took place at 70°C under room atmosphere. The change of σ with the temperature (T) and the decrease of σ with the thermal aging time (t) are consistent with a granular metal type structure, in which conductive grains are randomly distributed into an insulating matrix. Aging makes the grains shrink in a corrosion‐like process. From σ = σ(T) measurements the ratio s/d, where s is the average separation between the grains and d their diameter, as well as the rate d(s/d)/dt of their decrease with t were calculated. These revealed that the conductive grains consist of a shell, in which aging proceeds at a decreasing rate, and a central core, which is consumed at a much slower rate. Our measurements not only permitted the estimation of the shell thickness, which lies between 0 and 5 Å, but also gave quantitative information about the quality of the shells and the cores from their aging rates. The shells are consumed with an average rate of d(s/d)/dt = 6.6 × 10^?4 (h^?1), which is about 5 times greater than the more durable cores. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 117–122, 2005     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

Effect of the matrix crystallinity on the percolation threshold and dielectric behavior in percolative composites

Through the use of polyethylenes with different crystallinities as matrices, the effects of the matrix crystallinity on the percolation threshold and dielectric behavior of percolative composites have been investigated. The results suggest that the percolation threshold is negatively related to the matrix crystallinity, whereas the enhancement of the dielectric constant is positively related to the matrix crystallinity. A two‐dimensional diagram is proposed to illustrate such relationships. In addition, it has been found that the insulator–conductor transition is much flatter in low‐crystallinity‐matrix‐based composites, and this may be favorable for preparing threshold composites with a high dielectric constant and a low loss tangent. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Pb2+ binding by polyaspartyl polymers and their application to Pb2+ removal from glycyrrhizin

Polyaspartate is an excellent Pb²⁺‐binding agent in comparison with some polyaspartamide derivatives with different side chains, in that it possesses a higher Pb²⁺ uptake and a lower Pb²⁺ equilibrium concentration. Equilibrium sorption data for Pb²⁺ on polyaspartate can be well fitted with the Freundlich and Langmuir models. Experimental results show that a crosslinked polyaspartate hydrogel is superior to poly(acrylic acid)‐based resins and polystyrene‐based chelating resins. IR spectra and X‐ray photoelectron spectra reveal that the polyaspartate hydrogel binds Pb²⁺ by both an ion‐exchange mechanism and a chelating mechanism. The polyaspartate hydrogel is also an effective agent for the removal of Pb²⁺ from glycyrrhizin. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2215–2220, 2005     

Polyimides containing 4,4′‐bipyridinium units

New polyimides containing 4,4′‐bipyridinium units were synthesized by the reaction of bis(dichloromaleimide)arylene derivatives with 4,4′‐bipyridine in meta‐cresol. IR and ¹H‐NMR spectroscopy and elemental analysis as well confirmed their structures. The polymers were characterized by viscometric measurements, softening points, and thermogravimetric data. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2091–2100, 2004