Prediction of High-Temperature Long-Term Strength for Damaged Structures

A method is proposed for analytical estimation of the high-temperature long-term strength of structures with material discontinuities, which are stress raisers. We consider the processes involving the formation of diffusion pores. Diffusion processes in metals are strongly enhanced with increasing temperature and stresses.     

悬沙中D〉0．06mm粗粒的粒析级配组成及其改正方法

本文首先简述Ｄ＞０．０６ｍｍ泥沙的粒析沉降特性及其粒径偏粗的原因。继之对悬沙中粒径大于０．０６ｍｍ的粒析级配组成机理，及级配组成不同对标准粒径Ｄｂ与粒析粒径ＤＬ关系的影响进行了详细研究。在以上研究工作的基础上，开展了Ｄｂ与ＤＬ的比较试验，得出了粗、中、细型悬沙的Ｄｂ～ＤＬ关系和对ＤＬ的改正方法。     

Prediction of Final Product Properties After Cocurrent Spray Drying

The effect of drying and atomization conditions on the physical properties of powders for agglomerate-like materials and skin-forming material are studied in this article. A neural model is used for powder bulk and tapped density predictions.     

A New Image Analysis Based Method for Measuring Electrospun Nanofiber Diameter

In this paper, a new image analysis based method for electrospun nanofiber diameter measurement has been presented. The method was tested by a simulated image with known characteristics and a real web. Mean (M) and standard deviation (STD) of fiber diameter obtained using this method for the simulated image were 15.02 and 4.80 pixels respectively, compared to the true values of 15.35 and 4.47 pixels. For the real web, applying the method resulted in M and STD of 324 and 50.4 nm which are extremely close to the values of 319 and 42 nm obtained using manual method. The results show that this approach is successful in making fast, accurate automated measurements of electrospun fiber diameters.     

关于最远点判定及直径的唯一性

给出了点到有界集最远点的一些必要或充分条件，然后对直径的唯一性也给出了一些判定条件。     

Copper(II) removal from aqueous solutions by fly ash

The removal of Cu(II) by adsorption on fly ash has been found to be concentration, pH and temperature dependent. The kinetics of adsorption indicates the process to be diffusion controlled. The Langmuir constants have been calculated at different temperatures, and the adsorption has been found to be endothermic (ΔH = 15.652 kcal mol^?1). The maximum removal is observed at pH 8.0, and variation in adsorption with pH has been explained on the basis of surface ionisation and complexation.     

梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.     

安塞低渗油田孔隙结构对渗流特征曲线的影响

渗流曲线的测定是认识油藏流体渗流规律的基础。实验发现安塞油田储集层岩心渗流曲线在低有效净围压下近似表现为两段直线，通过压汞实验和毛管压力曲线数据分析，认为这种特征与储集层孔隙结构有关。在分析渗流特征时应综合考虑孔隙结核特征、流体与孔隙介质的相互作用等因素。     

熔体吹气发泡法制备泡沫铝合金研究

泡沫金属是近年来发展起来的一种新型材料。文章采用熔体吹气发泡法制备出了孔径为5．0—8．3mm，壁厚为0．040—0．076mm，密度为0．19—0．40g／cm^3，孔隙率为85．2％—93．0％的Al—Si泡沫铝合金，并着重讨论了发泡温度、气体流量、SiC粉末体积百分含量对泡沫铝合金形成的孔径和壁厚的影响关系。     

含杂质流体的流量测量

结合工程实例.介绍了几种实用的含杂质流体的流量测量方案,供自动化仪表设计及维堆护人员参考。