聚四氟乙烯薄膜压敏胶粘带的研制

主要介绍了聚四氟乙烯薄膜和有机硅压敏胶制造压敏胶粘带的方法。     

灞河生态治理工程模型试验研究

通过模型试验 ,对位于西安市东郊因采沙使河道破坏严重的灞河河段进行了复现试验和研究 ,并以此为依据 ,通过优化比较为设计部门提供了合理的橡胶坝坝址和坝座高程。在此基础上 ,又对建坝后橡胶坝对上下游冲淤变化的影响进行了试验研究和分析 ,解决了工程设计中的一些关键技术问题     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

变频调速技术在济钢焦化厂高压氨水泵上的应用

济钢焦化厂高压氨水泵变频调速系统采用变频器和PLC相结合的方式 ,具有调速精度高、节能等多种功能 ,保证氨水泵正常工作。全年可增加经济效益 77.3万元。     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

测量不确定度计算与实验方案的恰当选择

文章介绍了不确定度的定义及其一般计算公式，通过具体实例介绍了实验后不确定度的计算和实验前的误差估计。并对有多种可能的实验方案，利用误差估计的方法，选择出最佳的实验方案，使其不确定度最小。     

A new bubble-point-pressure correlation for the binary LiBr/H2O solution

In accord with the increasing concern about the global environmental issues, the absorption refrigeration heat-pump systems are currently being considered very promising and attractive. For the purpose of supporting the advanced R&D technology in this area, we have developed a novel correlation to represent the bubble-point pressures of LiBr H₂O solutions. The developed correlation covers the most extensive range of validity ever proposed: 273–483 K for temperatures, 0.05 kPa to 1.0 MPa for pressures. and 29 76 wt% LiBr for concentrations.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994. Boulder, Colorado, U.S.A.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

论高层建筑中央空调水系统水压试验的步骤

通过对中央空调水系统安装的特点分析,确定了应用效果良好的试压步骤。