Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

硫酸装置布朗扩散型纤维除雾器的现场测试

开发了一种用于布朗扩散型纤维除雾器的便携式现场测试装置，用这套装置可在现场测定纤维床阻力，从而对元件制造水平进行评价和比较，或在维修期间预测清洗后元件的操作性能。介绍便携式现场测试装置的设备布局、安装和运行，并对整体充填、平行缠绕、斜交叉缠绕纤维床及同心组合纤维床进行比较。此外，论述了硫酸装置工艺气体压降的价值。     

家电卷材涂料用HDI改性聚酯树脂的研制

以己二异氰酸酯（HDI）改性聚酯树脂与氨基树脂配制成家电用卷材涂料。阐述了氨酯键对涂膜性能的贡献。探讨了HDI用量对涂膜性能的影响。     

透明聚烯烃用成核剂合成的研究

介绍了聚烯烃成核剂合成反应所用助剂选择,反应条件的确立,利用均匀设计实现最佳配比实验,对不同侧基苯甲醛缩合反应进行了研究。     

Evidence for non-site-isolation in ZSM-5 from ion-exchange and catalytic studies

Ion exchange of HZSM-5 samples with alkali metal cations, using metal chloride solutions, results in partially exchanged zeolites, MHZSM-5, M = Li, Na, K or Cs. The degree of exchange is found to increase with increasing ionic radius of the cations. The catalytic properties of the alkalized zeolites were evaluated using the reaction conditions under which the catalytic activity of the HZSM-5 samples in terms of n-hexane cracking is proportional to the aluminium content. From the residual catalytic activity exhibited by the Na-, K- and CsHZSM-5 samples it is concluded that each of the larger Na⁺, K⁺ and Cs⁺ ions is influencing more than one AlO ₄ ^– tetrahedron, implying that the aluminium sites in ZSM-5 are not isolated. The ion-exchange results are then interpreted in terms of non-isolated aluminium sites. The ion-exchange and catalytic properties of the zeolites as a function of aluminium content are also discussed.     

试谈计算机软件测试管理的应用

计算机的软件测试是软件工程构成部分之一,同时软件测试也是检验软件开发人员及软件产品是否合格的重要凭据。就软件测试管理系统活动及应用两个方面的内容进行研究,并对管理工具的存在进行简单的介绍。     

试验温度和停放时间对胶料加工性能的影响

研究试验温度和停放时间对胶料加工性能的影响。结果表明，试验温度对胶料的门尼粘度、门尼焦烧时间和硫化特性均有一定影响。门尼粘度测定的试验温度选择100℃；门尼焦烧时间测定的试验温度一般选120℃，SBR胶料可提高至130℃左右，以缩短试验时间；硫化特性测定的试验温度一般选185℃。试验前模腔达到规定温度后再保持15min，以使转子与模腔温度一致。胶料停放时间应控制在2h左右。     

改进的APRIORI算法在试卷系统数据挖掘中的应用

本文通过对数据挖掘技术的研究,采用关联规则法对学生答题数据进行分析,并在关联规则使用中采用改进型的Apriori算法进行运算,构建高频集,并对于高分学生和低分学生的试卷进行了加权处理,使得高频集中的试题在知识点和难度上的关联更加突出,便于在自动组卷时更科学地评价试卷.     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.     

Available nitrogen in soils and its determination by the ‘Nmin-method’ and by electroultrafiltration (EUF)

Excess nitrogen fertilizer rates are an environmental hazard. To avoid excess rates, the level of available nitrogen in the soil must be known and considered for assessing the nitrogen fertilizer rate. In arable soils nitrate and exchangeable ammonium in the rooting depth of a crop are directly available to plant roots. These two nitrogen forms are recovered with the Nmin method and they are considered in assessing the nitrogen fertilizer rate for arable crops.Besides nitrate and ammonium recovered by the Nmin method from soil samples taken in early spring, a considerable amount of organic soil nitrogen may be mineralized during the growth period and contribute to crop nutrition. The nitrogen mineralization potential can be determined in incubation tests. The absolute quantities of mineralized nitrogen thus obtained, however, are much higher than the mineralization rates under field conditions. It is for this reason that incubation tests have not obtained a major importance for assessing nitrogen fertilizer rates.With the electro-ultrafiltration (EUF) method nitrate, ammonium, and a minor portion of organic soil nitrogen are extracted from a soil suspension. There is experimental evidence that this organic nitrogen (=Norg) is easily mineralizable. Based on field experiments with cereals and maize formulae were established by which the nitrogen fertilizer rate can be calculated. In these formulae nitrate, ammonium and organic nitrogen extracted by EUF are considered.Advantages and drawbacks of the Nmin method and EUF method are discussed.