101强化粉在水基涂料中的应用研究

叙述101强化粉在涂料中的应用,测定涂料的性能,研究101水基涂料对砂芯的渗透性,防止铁液浸渗的作用.生产结果令人满意.     

Modelling of plastic flow, heat transfer and microstructural evolution during rolling of eutectoid steel rods

A study was undertaken in an attempt to quantitatively describe the rolling process of eutectoid steel rods. Finite element method was employed to model plastic flow and heat transfer in the deformed material, and heat transfer during cooling to ambient temperature. The numerical calculation gave an assessment of the strain, strain rate and temperature distributions in the work piece. This allowed the prediction of the austenite microstructure evolution during the process. Finally, the relationships describing the microstructure-mechanical properties were used to quantitatively characterize the influence of processing parameters on strength of rods after rolling.     

球磨改性处理对Ti0．9Zr0．1Mn1．5合金相结构及储氢性能的影响

系统研究了Ti0．9Zr0．1Mn1．5储氢合金经不同时间（t=0min，10min，30min，60min）球磨改性处理后对其相结构及储氢性能的影响。结构分析表明，Ti0．9Zr0．1Mn1．5合金在球磨改性处理前后均由单一的六方结构的C14型Laves相组成；随着球磨时间的延长，合金粉的平均粒度减小，并出现了部分团聚现象。储氢性能测试表明，铸态合金经4次吸放氢循环后活化，室温最大吸氢量和有效放氢量分别为209．3ml／g和157．6ml／g，放氢率为75．3％；随着球磨时间的延长，合金的活化性能得到改善，室温最大吸氢量和有效放氢量均先升后降，且都在球磨30min时达到相应最高值231．4ml／g和203．8ml／g，放氢率达到88．1％。由此可见，适当的球磨改性处理能有效地改善Ti0．9Zr0．1Mn1．5合金的综合储氢性能。     

硅对定向凝固Ni3Al基合金IC6A微观组织和性能的影响

利用扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)、能谱(EDS)和X射线衍射(XRD)技术研究了硅对定向凝固Ni3Al基合金IC6A微观组织的影响。结果表明在IC6A合金中添加0．10％～0．20％Si(质量分数,下同)会使合金的枝晶间区析出块状的Mo1.24Ni0.76相和Mo6(Ni0.75Si0.25)7相,当硅的添加量达到0．30％时,合金的枝晶间区除了析出这两种相外,还有针状的δ-NiMo相析出。这相的析出不利于合金的高温持久性能,它们的硬度较大,只能通过孪晶的方式变形。硅有利于提高IC6A合金的高温抗氧化性能,而对合金的抗腐蚀性能和瞬时拉伸性能无明显影响。     

Ti-Al基合金中的Hall-Petch关系及影响因素分析

研究了全层片状组织Ti-Al基合金的室温拉伸性能与品团尺寸的关系。Ti-Al基合金的室温拉伸屈服强度和断裂强度与晶团尺寸成Hall-Petch关系。当合金中添加替代元素Cr和Nb时，其Hall-Petch斜率不变；而添加间隙元素C和B时，其Hall-Petch斜率增加。Ti-Al基合金的室温延伸率与晶团尺寸不满足Hall-Petch关系。     

Borides at interfacial zone of IC6 TLP bonded joints

1　INTRODUCTIONTransientliquidphase (TLP)bondingtechniquehasbeensuccessfullyusedinjoiningheatresistantal loys ,likeHastelloyX ,Inconel713C ,In10 0 ,Udimet5 0 0 ,70 0 ,MarM 2 0 0 ,0 0 7,2 4 7,30 2 ,Rene′80 ,TD NiCr ,MA75 4,6 0 0 0 ,PWA14 2 2 ,CSMX 2etc ,whicharesusceptibletohotcrackingor post weldheat treatmentcrackingproblemsduringfusionweld ing[14 ] .Inaddition ,therewerereportsofjoiningNiAlandTiAlintermetallicsbyTLPbondingmethod[510 ] .Forexample ,Galehadinvestigatedthemic…     

一种新的变轴数控机床标定方法

本文论述了国内外并联数控机床所采用的标定方法，选择了序列法进行了标定试验。但在实际标定过程中，出现了部分数据误差较大的问题，本文针对所面临的问题，提出了数值逼近法，并应用到实际机床的标定中，获得了机床的相关参数。之后，通过数学模型的计算值和实际测量值对比，验证了数据的可靠性，从而验证了方法的可行性和正确性。     

Prediction of particle motion in a two-dimensional bubbling fluidized bed using discrete hard-sphere model

The solids motion in a gas-solid fluidized bed was investigated using a discrete hard-sphere model. Detailed collision between particles and a nearest list method are presented. The turbulent viscosity of gas phase was predicted by subgrid scale (SGS) model. The interaction between gas and particles phases was governed by Newton's third law. The distributions of concentration, velocity and granular temperature of particles are obtained. The radial distribution function is calculated from the simulated spatio-temporal particle distribution. The normal and shear stresses of particles are predicted from the simulated instantaneous particle velocity. The pressure and viscosity of particles are obtained from both the kinetic theory of granular flow and the calculated stresses of particles. For elastic particles the individual lateral and vertical particle velocity distribution functions are isotropic and Maxwellian. The observed anisotropy becomes more pronounced with increasing degree of inelasticity of the particles.