碳纤维复合材料在某商场改造加固中的应用

结合中泰广场电梯的改造加固实例,阐述了碳纤维加固技术的应用,提出了碳纤维加固注意事项,进行了加固设计计算,展现了碳纤维加固技术的使用效果和应用前景,从而推广该技术。     

受压桁架式吊臂设计原理的研究

将起重量和起吊幅度为基本设计依据,以压杆稳定理论为分析基础,结合专业知识,建立物理模型,解决了起重量、起吊幅度与吊臂质量、吊臂主要参数之间的函数关系的难题,首次确定出设计参数的自然边界条件,为起重机设计者提供了确定设计参数的新方法和科学依据,具有开创意义。     

双笼型电机热态下起动的危害及预防

大容量的双笼型异步电机与同容量的单笼异步电机相比,具有起动力矩较大的特点,因此多用在载荷起动的机械设备上。通过对双笼型电机在热态下起动所造成危害的分析,提出预防措施,达到保护电气设备的目的。     

歧南洼陷西斜坡滩坝砂隐蔽油气藏研究与评价

通过岩心、测井、地震资料的综合研究及其层序界面的划分,歧南洼陷西斜坡,发育沙河街组滩坝砂、近岸水下扇及重力流水道等多种类型砂体。沙河街组底超、顶剥、中间相变明显,易形成多个层系、多种类型非构造圈闭。歧口凹陷西斜坡为继承性发育构造斜坡,是歧口凹陷油气运移的主要指向区,供油条件优越。广泛分布其间的的沙河街组三段滩、坝砂体平均孔隙度24.8%。平均渗透率175.5×10^-3μm²,具有高孔高渗特征。而且,滩、坝砂体沉积后没有遭受大规模构造运动破坏,油气保存条件有利。多年来的勘探成果,区内发现以歧647井油藏为代表的不整合油藏、以联盟为代表的上翘尖灭型油藏,以歧南9-1井为代表的构造-岩性油气藏等多种类型的油气藏,具备形成一定规模隐蔽油气藏的成藏条件。根据岩心相、测井相和地震相研究,预测歧南西斜坡沙三段低水位水下扇砂体及歧北斜坡的坡折带是下一步勘探的有利地区。其中,扣50南岩性圈闭及庄43井断块是最有利地区。     

基于单电流传感器的改进相电流重构技术

在电机闭环控制过程中,电流传感器故障、不同电流传感器的不一致性等因素可能导致系统失稳。为提高系统的容错能力,减小故障对控制系统稳定性的影响,提出一种基于单电流传感器的改进相电流重构技术。通过移动脉宽调制的脉冲矢量来消除母线电流采样盲区,进而通过母线电流重构获得三相电流。相比于传统电流重构方法,所提改进方法重构的电流更接近真实电流值,能够减小电流总谐波,降低电磁转矩脉动,提升系统的稳态性能。通过仿真和实验对比2种重构方法,证明了所提改进方法的优势。结果表明所提改进方法能有效实现电流重构,提升系统稳态性能。     

Novel insights on the impact of top water on Steam‐Assisted Gravity Drainage in a point bar reservoir

As efforts are made to efficiently exploit and recover bitumen resources in Canada, increasingly more complex reservoirs in the Athabasca area continue to challenge the application of Steam‐Assisted Gravity Drainage (SAGD) technology. Several studies have been done to investigate the impact of heterogeneities/complexities such as shale barriers, lean zones, and top and bottom water on the performance of the SAGD process. However, the literature is deficient for point bar deposits with top water zones, a common occurrence in oil sands systems. This study, by using thermal reservoir simulation, examines SAGD performance in a point bar deposit reservoir where an overlying top water and an inclined heterolithic strata (IHS) is present. The results show that where the top water is unconfined and steam injection pressure is higher than that of the top water zone, there is a loss of thermal energy, but the top water does not impact steam chamber development. At steam injection pressure lower than that of the top water zone, top water continuously drains into the reservoir and constrains the size of the chamber. However, the IHS zone helps to delay drainage of the top water into the chamber when steam is injected at underbalanced conditions. Finally, under proper steam injection pressure conditions, top water production can be considerably delayed.     

Effect of Adding Nitrogen on Microstructure and Property of Vanadium Microalloyed Reinforcing Bar Steel

Worldwideattentionhasbeenpaidtomicroal loyedsteelwhichhasbeendevelopedrapidly .Manyadvantagesofmicroalloyedsteelhavebeenrecog nizeddeeply .Firstly ,themicroalloyedsteelhashighstrengthand goodcomprehensiveproperties .Sec ondly ,highprofitscanbegainedduetolowerpro ductionandapplicationcost .Themicroalloyingele mentsareaddedtomicroalloysteelsforgrainrefin ingandprecipitationstrengthening[1] .　　Theabilityofsecondphaseparticlestomaintainfinegrainsizesathightemperaturebypinningmi gratingboundarie…     

凉水塔混凝土结构的腐蚀与防护

分析了大化肥凉水塔钢筋混凝土结构受体不水及大气的腐蚀渗透原因，提出了防护方法。     

Splicing of reinforcement bars with epoxy joints

The splicing of reinforcement bars in tension using epoxy-sleeve joints is described. The optimum length of the splicing sleeve required and the optimum bonding layer of epoxy resin in the joint were determined in direct tension tests. The performance of the epoxy-sleeve joint made to these optimum dimensions is then compared to that of a lap splice made according to the provisions of CP 110 in a beam flexure test. A sleeve length of 12 bar diameters and an optimum average thickness of 2 mm of the bonding layer of epoxy are shown to develop the full strength of the splices bar. Tensile reinforcement bars spliced using epoxy-sleeve joints are shown to perform satisfactorily as flexural reinforcement in beams and compare favourably with the standard CP 110 lap splice. Epoxy-sleeve joints are shown to produce stiffer beams and reduced crack width at the joints.     

MEASUREMENT OF K_(IC)OF MEDIAN OR LOW STRENGTH STEEL USING ROUND BARS WITH CIRCUMFERENCIAL CRACK

The size effect of tension round bars with circumferential crack was described and used tomeasure the plane-strain fracture toughness K_(1c) of median or low strength steel.The size ofcylindrical specimen required for K_(1c) measurement is much smaller than that of standardspecimen.The J-integral values of the cylindrical sqecimens were calculated to characterizethe size effect.The finite element calculution and fracture morphology analysis have beenconducted to eyplain the fact that smaller cylindrical specimen could be used to measureK_(1c) of median or low strength steel.