Molecular association complex of urea with polyethylene: 3. Structural studies of the complex

The crystal structure of urea-polyethylene complex in the hexagonal form, obtained by one of our preparation methods, is analysed by X-ray power diffractometry. In this analysis, the fixed molecular parameters of urea are used, and three models with respect to rotational disorder of the guest polyethylene molecule are assumed. It is shown that the host lattice structure constructed by urea molecules is essentially the same as that of urea-n-paraffin complex. Effects of the disorder structure of the guest on X-ray scattering of the complex are presented. However, there is a difficulty in identifying the disorder structure by X-ray analysis. With the aid of a potential energy calculation between the hexagonal urea tunnel and the guest molecule, a rotational disorder model is preferred.     

Characterization of microporous-mesoporous MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide

MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide either by a conventional method or by post-synthesis hydrothermal treatment were characterized by nitrogen adsorption in a wide range of relative pressure from 10^-6 to 1. Hydrothermally restructured samples were found to have lower BET surface areas, lower external surface areas and thicker silica walls than the non-treated sample. More importantly, in addition to their characteristic mesopores (ca. 3 nm), they were shown to have considerable amounts of micropores. The relative amount of micropores and mesopores was shown to be dependent on the treatment conditions. Thus, it is demonstrated that the postsynthesis hydrothermal restructuring is a convenient synthesis route to MCM-41 silicates with bimodal pore size distribution involving controllable amounts of microporosity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Mathematical models of the thermal decomposition of coal: 3. Density,porosity and contraction behaviour

Mathematical models are proposed to predict the true density of coal, semi-coke and coke and the porosity of a coke oven charge during carbonization. These models are combined in a further model which predicts the hitherto unexplained ‘twin-peaked’ contraction curve observed for semi-coke. It is found that the first contraction peak results from the relatively high rate of mass loss occurring towards the end of the primary devolatilization stage. The second peak occurs because of the increase in true density arising from the elimination of hydrogen from the semi-coke.     

Surface and subsurface products of the interaction of O2 with Ag under catalytic conditions

Polycrystalline Ag treated with O₂ at pressures up to 1 bar and at temperatures up to 920 K was examined by TDS. It was found that the peak commonly observed at 595±25 K and assigned to adsorbed atomic oxygen (O_a) is shifted to higher desorption temperatures with rising dosing temperatures. Since saturation of the uptake was not possible either, this peak was identified as dissolved atomic oxygen (O_d). The existence of a maximum for the O₂ uptake after exposure at 820 K was found. Hence, under conditions of formaldehyde synthesis ( 920 K) the ability of the catalyst to dissolve oxygen is near its maximum.     

Comparative analysis of methods for determining the metabolic rate in order to provide a balance between man and the environment

The incorrect determination of metabolic rate can be linked to discrepancies between the model of the PMV (Predicted Mean Vote) and real thermal sensation collected in field studies. Aiming to improve the correlation of the PMV model and the real thermal sensation, this work established new values for the metabolic rate: one way being called “calculated” using Newton's Method and the other called "measured" using a metabolic analyzer. Welder's activities were evaluated, through the measurements of environmental and personal variables. New values of metabolic rate were determined for this activity. The values found for the calculated form and the measured one were, respectively, 178.63 and 145.46 W/m², different from the range provided by the table of ISO 8996 (2004) for this activity (75–125 W/m²). In order to verify which of the values of the metabolic rate was closer to the real thermal sensation of PMV, a linear regression was made between the PMV and the real thermal sensation in three ways: S × PMV_tabulated (R² = 0.1749), S × PMV_calculated (R ² = 0.7481) and S × PMV_measured (R² = 0.7854). It was found that the values measured by the instrument gave a higher coefficient of determination which was chosen for the correction of the table. The correction of the table provides a value of M_predicted, that is a value of metabolic rate that corrects the values provided by the tables of ISO 8996 (2004), by means of a correction coefficient. For the welder's activities in a metal-mechanics industry, tabulated values can be multiplied by the correction coefficient 1.4648 in order to minimize inaccuracies. The PMV_predicted, obtained through the M_predicted, when related to the actual thermal sensation, provides a coefficient of determination of 0.7511, thereby improving the model of the PMV.     

Thermal conversion (visbreaking) of heavy Iraqi residue

A heavy Iraqi residue was thermally cracked using a soaker visbreaking process at temperatures between 435 and 480 °C, with a range of residence times of 43–109 s in the coil and 151–379 s in the soaker. The pressure was kept constant at 7 bar. Visbroken products were characterized, evaluated and fractionated into light, middle and heavy cuts. The stability of the visbroken products was compared with that of the original feedstock. Also an activation energy was calculated for the visbreaking process and related to the severity of the process. The results obtained show that the conditions used were not severe and could be applied to obtain a required conversion depending on the uses of the products.     

低密度泡沫玻璃的研究与应用

低密度泡沫玻璃是利用碎玻璃制造的一种气孔率大于90%的隔热保温材料,它具有强度高、导热系数小、吸水率低、不吸湿、耐腐蚀等特性,在潮湿环境下抗冻性能好,是一种优良的低温、超低温隔热保温材料。该产品用途广泛,所用的原材料简单易得,但生产工艺过程比较复杂,生产过程控制精度要求较高,容易产生各种缺陷而影响产品的质量。本文对低密度泡沫玻璃的生产工艺过程进行详细的分析研究,提出相应的措施,确保产品的低密度和高成品率,提高产品的性能,扩大产品的使用范围。     

MgO／Ni系梯度功能材料的设计与制备

对ＭｇＯ／Ｎｉ系梯度功能材料（ＦＧＭ），分别用实验和微观力学模型测定和计算了用于热应力缓和设计的各物性参数。讨论了两种结果之间存在差异的原因。用有限元方法模拟了制备过程中ＦＧＭ的热应力，得到ＭｇＯ／Ｎｉ系ＦＧＭ的综合设计准则。按设计结果进一步调整粉末工艺性质，成功地烧制出ＭｇＯ／Ｎｉ系ＦＧＭ。     

Preparations and properties of thermosensitive terpolymers of N‐isopropylacrylamide,sodium 2‐acrylamido‐2‐methyl‐propanesuphonate,and N‐tert‐butylacrylamide

Terpolymers based on N‐isopropylacrylamide, sodium 2‐acrylamido‐2‐methyl‐propanesulfonate, and N‐tert‐butylacrylamide were synthesized by free‐radical copolymerization with 2,2′‐azobisisobutyronitrile as an initiator. The lower critical solution temperatures (LCSTs) of the linear polymer aqueous solutions were determined by the measurement of the transmittance on UV at different temperatures. The influence of the polymer concentration, polymer composition, and ionic strength on the LCSTs of the linear polymers was investigated. The LCST decreased with increases in the hydrophobic monomer N‐tert‐butylacrylamide, polymer concentration, and ionic strength. The phase transition became sharp when the polymer concentration and ionic strength increased. Meanwhile, the crosslinked hydrogels were prepared with the same recipe used for the linear terpolymers, but a crosslinker was added to the reaction system. The swelling ratios of the hydrogels at various temperatures and salt solutions were determined. The hydrogels possessed both high swelling ratios and thermosensitivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis of tetramethyl-p-silphenylenesiloxanedimethylsiloxane triblock copolymer by employing living anionic polymerization

Dimethylsiloxane-tetramethyl-p-silphenylenesiloxane-dimethylsiloxane (DMS-TMPS-DMS) triblock copolymer was synthesized by employing living anionic polymerization of hexamethylcyclotrisiloxane (D₃). Two synthetic methods were carried out for the polymerization. One of those methods was the anionic polymerization of D₃ initiated at the silanolate anion which was prepared from the terminal hydroxyl group of silanol-terminated TMPS prepolymer by reaction with n-butyllithium (method 1). The other was the coupling reaction of vinyl-terminated TMPS prepolymer with hydrosilyl-terminated DMS prepolymer obtained from the anionic polymerization of D₃ by using diphenylmethylsilanolate anion as initiator (method 2). In method 1, DMS contents of the copolymers ranged from 25.8 to 72.5 wt% and the values agreed with the ratio of D₃ to TMPS prepolymer. The weight-average molecular weights ranged from 1.36×10⁴ to 19.4×10⁴ and were close to the predicted values calculated from the $\text{M}\text{?}{}_{\mathrm{v}}$ of the TMPS prepolymer and the amount of D₃ added. In the case of method 2, weight-average molecular weights ranged from 19.5×10⁴ to 24.2×10⁴. The high molecular weight copolymer could thus be obtained by method 2. Intrinsic viscosity values of the triblock copolymers agreed with calculated values obtained by considering the copolymer as a binary mixture of these homopolymers. Differential scanning calorimetry and thermogravimetry were carried out on the triblock copolymers. The equilibrium melting temperatures of each of the copolymers were very close to that of poly-TMPS (160°C). The glass transition temperature and heat of fusion were decreased as the DMS content was increased. The thermogravimetric curves for the copolymers indicated that the thermal stability of the triblock copolymer was intermediate between the DMS and TMPS homopolymers.