Fischer–Tropsch synthesis over Co–SiO2 catalysts prepared by the sol–gel method

Fischer–Tropsch synthesis was carried out in slurry phase over uniformly dispersed Co–SiO₂ catalysts prepared by the sol–gel method. When 0.01–1 wt.% of noble metals were added to the Co–SiO₂ catalysts, a high and stable catalytic activity was obtained over 60 h of the reaction at 503 K and 1 MPa. The addition of noble metals increased the reducibility of surface Co on the catalysts, without changing the particle size of Co metal significantly. High dispersion of metallic Co species stabilized on SiO₂ was responsible for stable activity. The uniform pore size of the catalysts was enlarged by varying the preparation conditions and by adding organic compounds such as N,N-dimethylformamide and formamide. Increased pore size resulted in decrease in CO conversion and selectivity for CO₂, a byproduct, and an increase in the olefin/paraffin ratio of the products. By modifying the surface of wide pore silica with Co–SiO₂ prepared by the sol–gel method, a bimodal pore structured catalyst was prepared. The bimodal catalyst showed high catalytic performance with reducing the amount of the expensive sol–gel Co–SiO₂.     

聚氯乙烯塑料中多种邻苯二甲酸酯类增塑剂的同时测定

为了在线监控聚氯乙烯塑料中增塑剂的含量,利用傅立叶变换红外光谱法-ATR技术测定样品的红外光谱,采用偏最小二乘法对所测红外光谱进行分析,建立了一种无损快速分析方法,定量地测定聚氯乙烯塑料中多种邻苯二甲酸酯类增塑剂的含量。该方法测量精密度的变异系数小于6%,测量准确度的变异系数小于3%。该方法不受基体的干扰,简单快速,适合于流水线的质量控制。     

一步法生产涤纶FDY工艺的探讨

利用ＫＶ７３１纺丝设备一步法生产出涤纶ＦＤＹ，探讨了热辊拉伸和熔体温度对纤维质量的影响。采用高特性粘数的聚酯切片，严格控制纺丝工艺，可以在５０００ｍ／ｍｉｎ的纺丝速度下纺制高质量的细旦涤纶ＦＤＹ。     

十四醇聚氧化烯烃醚琥珀酸单酯磺酸盐的表面活性研究

合成了一系列十四醇聚氧乙烯醚和聚氧丙烯醚琥珀酸单酯磺酸盐，比较了其临界胶束浓度、润湿力、起泡力等表面活性     

复分解法制备磷酸二氢钾的研究

介绍了以工业氯化钾和工业磷酸为基本原料，采用复分解法，在氯化钾过量的情况下，加入氨水作为pH值调节剂，制备磷酸二氢钾（KH2PO4）的研究。产品含量大于92％，原料转化率（以磷酸计）大于85％，无三废产生。     

铬酸酐副产物硫酸氢钠的利用

对生产铬酸酐时副产的含铬硫酸氢钠的利用作了评论，介绍了8种方法，即，化学沉淀法、磷酸沉淀法、铬酸铬法、电解氧化法、过硫酸钠氧化法、制商品硫酸氢钠、酸泥制碱式硫酸铬、硫酸氢钠制碱式硫酸铬，其中以化学沉淀法、磷酸沉淀法和铬酸铬法应用最广。     

Use of laser scanning confocal microscopy for characterizing changes in film thickness and local surface morphology of UV-exposed polymer coatings

Laser scanning confocal microscopy (LSCM) has been used to characterize the changes in film thickness and local surface morphology of polymer coatings during the UV degradation process. With the noninvasive feature of LSCM, one can obtain thickness information directly and nondestructively at various exposure times without destroying the specimens or deriving the thickness values from IR measurement by assuming uniform film ablation. Two acrylic polymer coatings were chosen for the study, and the physical and chemical changes of the two systems at various exposure times were measured and analyzed. Those measurable physical changes caused by UV exposure include film ablation, formation of pits and other surface defects, and increases in surface roughness. It was found in both coatings that changes in measured film thickness by LSCM were not correlated linearly to the predicted thickness loss using the changes in the CH band obtained by the Fourier Transform Infrared (FTIR) spectroscopy measurements in the later degradation stages. This result suggested it was not a uniform film ablation process during the UV degradation. At later stages, where surface deformation became severe, surface roughness and profile information using LSCM were also proven to be useful for analyzing the surface degradation process Presented at the 81st Annual Meeting of the Federation of Societies for Coatings Technology, November 13–14, 2004 in Philadelphia, PA.     

Fabrication of Porous SiC Ceramics with Special Morphologies by Sacrificing Template Method

Sacrificial template technique is widely used in producing porous materials with controlled morphologies and tailored properties. In this paper, unique templates such as filters, carbon nanotube, carbon fiber and silica were used to make porous SiC ceramic with special morphologies. Template derived porous ceramic plates, SiC nano-net, fiber-inverse and bead-inverse porous SiC ceramic were successfully prepared from the preceramic precursor, polymethylsilane (PMS). The synthesis procedures were involved with the infiltration of the templates with appropriate concentration of the preceramic polymer, their curing, pyrolysis and subsequent template removal. The synthesized porous SiC was characterized by SEM, TEM, XRD and BET methods.     

美国三元乙丙防水片材接缝技术

介绍了美国三元乙丙防水片材接缝技术的发展历程并介绍了二十世纪八十年代以来有关的专利技术和测试方法。     

Surface activity of quaternary ammonium salts derived from jojoba oil

A number ofcis andtrans quatenary ammonium salts were synthesized from jojoba oil. All derivatives were found to be surface active agents, i.e., they reduced the surface tension to 35 dynes/cm⁻¹, at very low concentrations. The relationship between the surface activity and the molecular structure is discussed.