企业实施精益生产的探讨

通过描述造成企业经济效益差的原因之一——浪费，提出了如何实施精益生产，消除企业浪费，以提高企业经济效益．     

Prediction of spectral reflectance factor distribution of automotive paint finishes

It is necessary to determine the accurate reflectance of painted surfaces for the review of paint finishes by computer graphics (CG) before actual painting of the exterior color of automobiles, and for quality control during production and inspection processes. We have optimized a method for measuring reflectance by using a statistical technique. We have found that the reflectance of a painted surface is best measured at an incident angle of 60° and at five aspecular angles of 10°, 18°, 28°, 40°, and 90°. Our method makes it possible to accurately reproduce reflection characteristics of paint finishes containing special flake pigments, such as pearl mica. Also it was proved that our method can apply not only to solid and metallic coatings but to all painted surfaces. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 275–282, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20125     

压水堆硼稀释事故的计算

一、概述核电厂压水堆的初始过剩反应性是通过控制捧、固体可燃毒物和溶解在主回路冷却剂中的硼酸等三种方式联合控制的。随着反应堆的燃耗和裂变毒物的积累,堆的过剩反应性不断减少,需要通过化容系统,控制硼酸的浓度来进行补偿。如果化容系统发生故障或操作员误操作,就会给回路注入无硼或低于规定浓度的补给水,给反应堆引入正反应性,造成硼稀释事故。按核安全法规的要求,应对换料、冷停堆、热停堆和启动等工况进行计算,并要求在这些     

多丝正比室中电子的最大漂移时间

多丝正比室中电子的最大漂移时间是逃逸门电路中的一个重要参数。这个参数的选择将影响逃逸门工作方式的多丝正比室的整体性能。通过实验测量得到了多丝正比室中电子的最大漂移时间的实际值和最大漂移时间随多丝正比室工作状态的变化，测量结果在实际中得到应用。     

Gelling of alginate fibres

Equipment was developed to measure the time for complete gelling of sodium alginate fibres in calcium chloride solution, taken as the time to achieve maximum tensile strength. The effects of fibre diameter, alginate concentration, alginate composition and calcium chloride concentration on gelling time were investigated. A diffusional model, developed to predict the gelling time, agreed with experimental results except for the effect of calcium ion concentration which was modelled empirically.     

单光子时间分辨在线谱仪系统中的接口电路

本文介绍单光子时间分辨在线谱仪系统中的多道分析器与IBM PC/XT微型计算机接口的工作原理及控制程序。     

Lyapunov‐stable discrete‐time model reference adaptive control

Discrete‐time model reference adaptive control (MRAC) is considered with both least squares and projection algorithm parameter identification. For both cases complete Lyapunov proofs are given for stability and convergence. The results extend the approach of Johansson (Int. J. Control 1989; 50 (3):859–869) to include Lyapunov stability for MRAC when the normalized projection algorithm is used for parameter identification. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.