Analysis of the oscillatory behavior of double-walled carbon nanotube-based oscillators

Molecular dynamics simulations of oscillatory behaviors of double-walled carbon nanotube-based oscillators are performed. The second-generation empirical bond-order potential is used for the atomic interactions within a wall, and a registry-dependent and four different registry-independent van der Waals potentials are used for the atomic interactions between walls. It is found that the frequencies of the nanotube oscillators are sensitive to the choice of the van der Waals potentials. An almost non-decay oscillation is observed for the registry-dependent potential when there is no rocking motion. However, an apparent decay oscillation is observed when rocking motion occurs. A decay oscillation is observed for all registry-independent potentials even without rocking motion. Mechanisms leading to unstable oscillatory behavior are analyzed.     

富集均三甲苯塔的模拟与优化

在满足工艺要求的基础上，通过富集均三甲苯塔模拟与优化给出最佳操作条件，用于指导实际操作和设备改造．优化生产参数。     

SIMULATION AND ESTIMATION OF LONG MEMORY CONTINUOUS TIME MODELS

Abstract. Some general properties of long memory continuous time processes are recalled or proved. Methods of simulation are studied. A comparison with the usual discrete time autoregressive fractionally integrated moving-average filter is made and illustrations are provided. Then, two methods of estimation of the parameters of such a model from a discrete sample are studied, both theoretically and empirically, with Monte Carlo experiments.     

射流流化床内流体力学行为的模拟研究

以流化床应用为代表的气固流动系统是许多化工过程中的重要组成部分 ,CFD( computational fluid dynamics)方法能够为其优化设计和放大提供所需要的信息 .本文采用双欧拉模型 ,与 Gidaspow等的实验结果进行了对比 ,模拟了二维射流流化床内气泡的形成规律 ,得到了带锥型分布器的流化床内瞬时空隙率和气固相速度分布等流体力学参数 .对锥型分布器流化床的实验结果表明 ,模拟得到的气泡的形状与实验现象相接近 .     

Modeling of fast pulse responses in the Multitrack: an advanced TAP reactor

A detailed transport model for the Multitrack setup, a TAP-like system, has been developed, which allows further analysis of adsorption, diffusion and catalysis phenomena. This includes the transport in the void part between the pulse valve and the reactor inlet. The effects of viscous flow and thermal transpiration, aspects that have not been studied in detail before for this type of setup, have been analyzed. A new expression for the modeling of the output signal is proposed depending on the positioning of the MS detector used in the study. The transport parameters of the model have been estimated by the analysis of the experimental pulse responses of the empty reactor system and the reactor charged with an inert packed bed. The proposed model reproduces the experimental pulse responses very well, and therefore can be extended to study systems with reacting or adsorbing beds by including the corresponding rate equations for the processes occurring in the bed of particles.     

Important issues in a molecular dynamics simulation for characterising the mechanical properties of carbon nanotubes

This paper discusses several important issues in a molecular dynamics simulation for analysing carbon nanotubes and their mechanical properties. In particular, the paper addresses the problems in selecting appropriate inter-atomic potentials, number of thermostat atoms, thermostat techniques, time and displacement steps and number of relaxation steps to reach the dynamic equilibrium. Based on these, the structural changes of armchair and zigzag nanotubes and their mechanical properties are investigated. The Young's modulus and Poisson's ratio of the armchair tube are 3.96 and 0.15 TPa, respectively, and those of the zigzag tube are 4.88 and 0.19 TPa, respectively. The best simulation technique identified in this study predicts that the ultimate tensile strain of a carbon nanotube is around 40% before atomic bond breakage.     

Interbay物料自动搬运系统性能分析

Interbay物料自动搬运系统的运行效率对于晶圆制造系统影响较大,研究Interbay物料自动搬运系统的绩效具有较大的意义[1]。该文以带有捷径的单闭环背脊式布局的物料自动搬运系统为研究对象,通过问题描述,简化、假设将实际问题抽象为导引运输模型。然后,建立数学模型,采用Dijkstra算法确定工件搬运的最短路径。最后,利用Arena仿真软件建立含有导引运输设备的模型,采用控制变量法探究小车数量小车占用轨道的方式、调度规则等因素对于产出的影响,发现对于本文中的模型,其它条件相同时,搬运系统采用Release-at-end的控制方式,系统最大搬运量越大。     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...